Kohler Command PRO CH640 Manuale d'uso - Pagina 10

Sfoglia online o scarica il pdf Manuale d'uso per Motore Kohler Command PRO CH640. Kohler Command PRO CH640 21. Liquefi ed petroleum gas (lpg) or lpg/natural gas (ng) fueled
Anche per Kohler Command PRO CH640: Manuale d'uso (21 pagine), Manuale d'uso (8 pagine), Manuale d'uso (12 pagine), Manuale d'uso (8 pagine)

Stampa la pagina

Change Oil Filter

Replace the oil ﬁ lter at least every other oil change

(every 200 hours of operation). Always use a genuine

Kohler oil ﬁ lter. Use chart below to determine part

number to order.

Oil Filter Part No.

12 050 01-S

52 050 02-S

Replace the oil ﬁ lter as follows:

1. Drain the oil from the engine crankcase by

removing one of the drain plugs and allowing

ample time for complete drainage.

2. Before removing the oil ﬁ lter, clean the area

around the oil ﬁ lter to keep dirt and debris out

of the engine. Remove the old ﬁ lter. Wipe oﬀ the

surface where the oil ﬁ lter mounts.

3. Place a new replacement ﬁ lter in a shallow pan

with the open end up. Pour new oil of the proper

type in through the threaded center hole. Stop

pouring when the oil reaches the bott om of the

threads. Allow a minute or two for the oil to be

absorbed by the ﬁ lter material.

4. Apply a thin ﬁ lm of clean oil to the rubber gasket

on the new ﬁ lter.

5. Install the new oil ﬁ lter to the ﬁ lter adapter or oil

cooler. Refer to instructions on the oil ﬁ lter for

proper installation.

6. Reinstall the drain plug. Make sure it is tightened

to 13.6 N·m (10 ft . lb.) torque.

7. Fill the crankcase with new oil of the proper type

to the F mark on the dipstick.

8. Test run the engine to check for leaks. Stop the

engine, allow a minute for the oil to drain down,

and recheck the level on the dipstick. Add more

oil as necessary so the oil level is up to but not

over the F mark on the dipstick.

Service Precleaner and Air Cleaner Element

This engine is equipped with a replaceable, high

density paper air cleaner element. Most engines are

also equipped with an oiled, foam precleaner which

surrounds the paper element. See Figures 8 and 9.

Air Cleaner Cover

Length

2-1/2"

3-3/8"

Figure 8. Air Cleaner Housing Components.

Element Cover

Figure 9. Air Cleaner System Components.

Check the air cleaner daily or before starting the

engine. Check for a buildup of dirt and debris around

the air cleaner system. Keep this area clean. Also

check for loose or damaged components. Replace all

bent or damaged air cleaner components.

NOTE: Operating the engine with loose or

Service Precleaner

If so equipped, wash and reoil the precleaner every 25

hours of operation (more oft en under extremely dusty

or dirty conditions).

1. Loosen the cover retaining knob and remove the

2. Remove the precleaner from the paper element.

3. Wash the precleaner in warm water with

4. Saturate the precleaner with new engine oil.

Air Cleaner Cover Knob

Element

damaged air cleaner components could

allow unﬁ ltered air into the engine causing

premature wear and failure.

cover.

detergent. Rinse the precleaner thoroughly until

all traces of detergent are eliminated. Squeeze out

excess water (do not wring). Allow the precleaner

to air dry.

Squeeze out all excess oil.

Element Cover Nut

Precleaner