Kohler 14RESA Manuale di istruzioni per l'installazione e il funzionamento - Pagina 3
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione e il funzionamento per Generatore portatile Kohler 14RESA. Kohler 14RESA 37. Residential/commercial generator sets
Anche per Kohler 14RESA: Istruzioni per l'installazione (4 pagine), Manuale di risoluzione dei problemi (8 pagine), Istruzioni per l'installazione (2 pagine), Funzionamento (20 pagine)
Stampa la pagina
Related Literature
A single-phase paralleling system is made up of the
APM module covered by this instruction sheet plus two
generator sets and a Model RXT transfer switch. A load
control module (LCM), load shed kit, or combined
interface/ load management board on the RXT is
required if one generator set cannot support the
maximum total load. An optional PIM and OnCuer Plus
monitoring system may also be used with the power
system. Refer to the documentation provided with the
other system components for installation instructions.
Related literature is listed in Figure 4.
Document Description
SiteTecht Software Operation Manual
OnCuer Plus Operation Manual
OnCuer Plus Technical Manual
Installation Manual, 14/20RESA, 20RESC
Operation Manual, 14/20RESA, 20RESC
Installation Manual, 20RESB, 20RESD
Operation Manual, 20RESB, 20RESD
Installation Manual, 14RCA and 20RCA
Operation Manual, 14RCA and 20RCA
Operation/Installation Manual, Model RXT
Transfer Switch
Installation Instructions, Load Control Module
(LCM)
Installation Instructions, Programmable
Interface Module (PIM)
Installation Instructions, Load Shed Kit
Figure 4 Related Literature
Safety Precautions
Observe the following safety precautions while installing
the kit.
WARNING
Accidental starting.
Can cause severe injury or death.
Disconnect the battery cables before
working
on
Remove the negative (- ) lead first
when disconnecting the battery.
Reconnect the negative (- ) lead last
when reconnecting the battery.
TT-1596
8/22
Part Number
TP-6701
TP-7006
TP-7007
TP-6803
TP-6804
TP-6925
TP-6926
TP-7091
TP-7092
TP-6807 or
TP-7193
TT-1574
TT-1584
TT-1609
the
generator
set.
Disabling the generator set.
cause severe injury or death.
generator set or equipment connected to the set, disable the
generator set as follows: (1) Press the generator set off/reset
button to shut down the generator set. (2) Disconnect the
power to the battery charger, if equipped. (3) Remove the
battery cables, negative (- ) lead first. Reconnect the negative
(- ) lead last when reconnecting the battery. Follow these
precautions to prevent the starting of the generator set by the
remote start/stop switch.
DANGER
Hazardous voltage.
Will cause severe injury or death.
Disconnect all power sources before
opening the enclosure.
Grounding electrical equipment. Hazardous voltage will
cause severe injury or death. Electrocution is possible
whenever electricity is present. Ensure you comply with all
applicable codes and standards.
generator set, transfer switch, and related equipment and
electrical circuits. Turn off the main circuit breakers of all
power sources before servicing the equipment. Never contact
electrical leads or appliances when standing in water or on wet
ground because these conditions increase the risk of
electrocution.
Short circuits.
Hazardous voltage/current will cause
severe injury or death. Short circuits can cause bodily injury
and/or equipment damage.
connections with tools or jewelry while making adjustments or
repairs. Remove all jewelry before servicing the equipment.
Making line or auxiliary connections. Hazardous voltage
will cause severe injury or death. To prevent electrical
shock deenergize the normal power source before making any
line or auxiliary connections.
Electrical backfeed to the utility. Hazardous backfeed
voltage can cause severe injury or death. Install a transfer
switch in standby power installations to prevent the connection
of standby and other sources of power. Electrical backfeed
into a utility electrical system can cause severe injury or death
to utility personnel working on power lines.
Accidental starting can
Before working on the
Electrically ground the
Do not contact electrical
3