Bil-Jax 4527A Informazioni operative e di sicurezza - Pagina 7
Sfoglia online o scarica il pdf Informazioni operative e di sicurezza per Sollevatori a braccio Bil-Jax 4527A. Bil-Jax 4527A 13. Articulate boom lift
Stampa la pagina
G. CONTROLS and THEIR FUNCTIONS;
PLATFORM CONTROL STATION;
16 - 17. PLATFORM TILT BUTTONS;
button at the same time to level the work platform (levels the platform only, not the boom lift).
There is a power outlet located in the boom lift platform area. It is provided for running
NOTE;
electrical power tools from the work platform. A connecting power cord must be plugged into a
suitable power source. The power plug is located on the trailer frame, in the front of the
accessory equipment stowage plate. The outlet is rated for a 15-ampere load. Do not overload
the accessory power circuit.
H. OPERATION INSTRUCTIONS;
NORMAL OPERATING PROCEDURES;
pages; 18-19)
1. Read and follow all safety precautions and operating instructions, as well as all applicable government
regulations.
2. Conduct a "Pre-Operation Inspection"
(Refer to
E. USAGE RESPONSIBILITIES - above
4, under Daily Service Checks, pages; 26-27 for more information).
3. Position the boom lift at the work area. Make sure the boom lift is on a firm and level surface and there
are no potential hazards. (as describe in section "
4. Apply the parking brake or chock the wheels
5. Lower the tongue jack and unhitch the boom lift from the tow vehicle.
Unhitch the boom lift from the tow vehicle prior to operating. Failing to unhitch the
WARNING;
boom lift, can lead to the boom lift becoming unstable which can lead to personnel injury or
death. It can also do damage to the equipment and / or the tow vehicle.
6. Turn the key switch on Ground Control Station to operate ground controls. If power does not come on,
make sure both emergency
disconnect is plugged in.
7. The control microprocessor will perform self-diagnostic to test the operating system. After several seconds,
the
DISPLAY PANEL
8. Verify that the control status indicator
the outriggers buttons will not work. A flashing control status
booms is raised and needs to be stowed. (refer to Figure 3-1 and Figure 3-3)
9. Extend the outriggers manually or using the
buzzer will sound and two
be lit.
Press and hold the
AUTO LEVEL;
MANUAL LEVEL;
outriggers by pressing the
10. Verify that the auto level indicator
indicator is not lit, the boom may not be level.
11. Pull the latch release on the boom travel latches, raise the
latch handle and swing the latch U-bolt down.
12. Verify that the platform is properly attached to the mounting
bracket on the boom end. The "Retaining Pin" should be fully
inserted through the platform and the mounting bracket on
the boom end.
Failure to verify proper attachment of the
WARNING;
platform to the boom end could cause the platform to
separate from the boom, resulting in serious injury or
death to the operator.
13. Use the ground control panel to operate the boom lift functions. Raise, lower, extend and rotate the boom
by pressing and holding the desired
the location and function of all controls. Learn to smoothly start and stop all boom motions.
14. Fully lower the boom onto the boom rest to position the platform for boarding. Turn the key switch to the
platform control position.
15. Raise the safety bar and enter the work platform. Put on the safety harness and attach the lanyard to
the "Fall Protection Attachment Point" on the side of the platform support beam.
16. Become familiar with the location of all controls. Use the platform control panel to operate the boom lift
functions. Raise, lower, extend and rotate the boom by pressing the desired
at the same time. Learn to smoothly start and stop all boom motions.
17. Should the platform become tilted out of the normal vertical axis, press and hold the desired
button and one of the
18. Monitor the Battery Condition Indicator during operation and charge the batteries as necessary.
2015 - BIL-JAX #4725A, "TOWABLE - ARTICULATE BOOM LIFT" - OPERATIONAL & SAFETY INFO
Press and hold and hold any
(for further information, see Manufacturer's "Operator Manual",
, Also refer to the Manufacturers "Operator Manual", section
buttons (ground and platform) are pulled out and the main power
STOP
window will read;
BIL-JAX
A STEP ABOVE
is lit. If the control status indicator
LED
AUTO LEVEL
s at each
LED
OUTRIGGER
and
EXTEND
Extend the two outriggers closest to the trailer coupler first. Lower each pair of
button
EXTEND
is lit. If the auto level
LED
and function buttons at the same time. Become familiar with
SPEED
buttons at the same time to adjust.
PLATFORM TILT
button and the desired
SPEED
F." USAGE RESPONSIBILITIES - Work Safety, above).
LED
indicates that one or more of the
LED
button. When the boom is leveled properly, a
button and the
at the
LED
buttons at the same time.
AUTO LEVEL
SPEED
PLATFORM TILT
is not lit or is flashing,
button will
AUTO LEVEL
and function buttons
SPEED
...
page 7 - 12