Billi B-6000 Manuale di installazione - Pagina 2

Sfoglia online o scarica il pdf Manuale di installazione per Sistema idrico Billi B-6000. Billi B-6000 4. Boiling and chilled filtered water system
Anche per Billi B-6000: Manuale d'uso (17 pagine)

Stampa la pagina

Installation

requirements.

—Billi B–6000 system components

Before commencing installation,

ensure you have identified the following:

1. Underbench module

2. Dispenser upper with tubing

3. Dispenser base & mount

4. Barb locking bush

5. 4mm chrome screw & allen key

6. Large washer

7. Tube spring clamps x 3

8. 450mm flexible braided hose

9. Drain fittings including

John guest fittings

10. 3/8 tube connected with adapter

to 3/16 black tube

11. ½ inch drill bit

12. Behind door panel:

a. filter cartridge(s)

b. user guide

c. warranty registration card

—Determine unit location

Plan the installation. Dispenser tube lengths,

position of power and water outlets, required

air space around the underbench module and

access for service must be considered before

cutting tube lengths. Refer to Diagrams 1 and 2

and the table below for clearances around unit.

Unit must be installed horizontally with display

panel facing to front of cupboard. The B-6000 is

designed for internal installation only.

Model

B-6000

Height

340mm

Width

315mm

Depth

350mm

Min side clearance

10mm

—Water supply

The B-6000 must only be connected to

a cold water supply. A 15mm stop tap

(not supplied) is to be installed in an easily

accessible position within 450mm from

the B-6000 water supply inlet. The B-6000

incorporates a certified pressure limiting

and backflow prevention device.

Do not fit an additional pressure

limiting valve.

Water supply pressure:

Min. 250kPa, max. 1000 kPa.

Supply temp: min. 5°C, max. 30°C.

Do NOT install with water that is

microbiologically unsafe or with water of

unknown quality without adequate disinfection

before or after the system. Systems certified

for cyst reduction may be used on disinfected

water that may contain filterable cysts.

—Power requirements

A single 3 pin GPO is required. A dedicated

circuit should be provided and must be

fitted with an earth leakage protection

device (RCD). An externally fitted RCD device

is acceptable. All B-6000 models are supplied

with a 1-metre flex cord and plug.

—Drainage

B-6000 models require a drainage point such

as a dishwasher nipple. Use the nipple adaptor

fitting supplied or the clamp-on drain adaptor

(also supplied with system). Clamp-on drain

adaptor must be installed above the water seal

on the sink side of the water trap. The B-6000

dispenser incorporates an externally vented

air gap.

Power

outlet

800mm

tube

length

supplied

Stop-tap

(installed by plumber)

20mm

175mm

205mm

10mm

bench

thickness

1mm-48mm

35mm

95mm

Installing the

dispenser.

IMPORTANT: This Billi appliance is to be

installed by a licensed tradesperson in

accordance with AS 3500.4 or AS/NZ 3500.4.2

and in compliance with applicable state

regulatory requirements. For correct operation

of this appliance, it is essential to observe the

manufacturer's instructions.

1. Install dispenser assembly

Determine position of dispenser mounting

hole in sinktop or benchtop. Dispenser base

template (Diagram 3) may be cut out and

used to assist in correct positioning. Hole size

required is ø32mm.

—Stainless steel sinktop

A suitable 32mm hole punch (Part no: 857901)

is available as an accessory

from Billi Pty Ltd. If possible, cut hole with

150mm

die mounted below the sinktop surface so

min

clearance

that burr is pulled downwards. Alternatively,

remove burr and radius edge of hole with fine

file. This allows barbed dispenser mount to

slide smoothly into mounting hole. Oil hole

punch regularly. Lubricate surface to be cut

with detergent.

—Timber/laminate benchtop

Maximum benchtop thickness is 50mm.

Cut 35mm hole in appropriate position.

When drilling through a particle board

bench top, take care to avoid a large chip

Diagram 1

breaking away as drill breaks through

underside surface. We recommend drilling

a small pilot hole through benchtop, partially

drilling the 35mm hole from underneath and

then completing drilling the hole from above.

The large 30mm washer supplied may be used

to secure barb where underside particle board

bench top has chipped away.

130mm

2. Activate Dispenser Swivel Feature

To activate the swivel feature of your

dispenser, you will need to remove the

locking piece from the dispenser base.

Simply push out the piece as show in

Diagram 5. This will allow the tap to

move 45 degrees to the left and right.

3. Fit dispenser base

a. Cut a 32mm hole in sinktop or benchtop.

Diagram 2

Remove burr if protruding upwards.

b. Press barbed mounting shaft through

mount hole. Finger tighten nut.

c. Insert barb locking bush as shown

in Diagram 6.

d. Ensure barb is centred in mount hole

before tightening. Check position of

base ring and gasket.

e. Moderately tighten locking nut using

multigrips or spanner. Take care to avoid

overtightening nut which may break the

plastic threaded shaft.

Place large washer over thread as shown

in Diagram 7.

g. Cut off excess threaded shaft with a

hacksaw, using washer as a cutting guide.