CPC SS-100 Manuale di installazione e programmazione - Pagina 12

Sfoglia online o scarica il pdf Manuale di installazione e programmazione per Server CPC SS-100. CPC SS-100 13. Serial server

Stampa la pagina

Connect 25-pin female end of DB25/DB9

STC adapter to the 25-pin male port of the

SS-100, or the 25-pin male end of the DB25

null modem adapter.

Connect the female end of 10' DB9 serial ca-

ble to the male end of DB25/DB9 STC adapt-

er. If the RS232 connection is female, (i.e.

535-1190 DB9 computer to REFLECS con-

troller laptop cable).

Connect the male end of the 10' DB9 serial

cable to the female end of the DB9 RS232 ca-

ble.

If the RS232 connection is male, (i.e. 812-

1800 RS232 Remote Communications Bus

Amplifier), connect the DB9 female/female

STC gender changer to the male end of the

10' DB9 serial cable.

Connect the other end of the DB9 female/fe-

male STC gender changer to the male end of

the DB9 RS232 cable.

3.5.

Install the COM Port Redirec-

tor Software on remote Com-

puter

Insert COM Port Redirector CD-ROM into

CD-ROM drive and select Install Comm

Port Redirector. Redirector Driver Installa-

tion should automatically start up.

Note: If you have Autorun disabled in Windows you

will have to manually start the installation program. Go to

Start|Run|Browse and select your CD-ROM drive. Dou-

ble-click on "red32bit", then click OK.

The Redirector Welcome window will pop

up; click Continue.

The installer will start up and the Welcome

window appears; click Next.

10. The Choose Destination Location window

will pop up; click Next.

11. The Select Program Folder window ap-

pears; click Next.

12. The Setup Complete window will pop up

and prompt you to restart the computer. Click

Finish and wait for your computer to boot up.

3.6.

Configure the COM Port Re-

director

13. Start the COM Port Redirector Configuration

Program (RDCfg) by selecting: Start|Pro-

12 • Install the COM Port Redirector Software on remote Computer

grams| Redirector|Configuration to open

the RDCfg dialog box.

14. If you are installing more than one site on the

computer, you will have to select Com Setup

in the RDCfg dialog box and click the check

boxes on more COM ports in the Port Setup

dialog box to be able to have more than one

port to select for configuration.

15. In the Port Configuration box under Redi-

rect COMx To:, where x is the COM port

number, select the correct COM port from the

dropdown list to redirect to the IP address

(i.e. Redirect COM3 To:).

16. In the Port Configuration box select Add IP

to open the IP Service Setup window.

17. In the Host: field, type the IP address of the

SS-100 from Step 3 in Section 3.3., Set up

SS-100 From the Local_1> Command

Prompt of this manual. In the form:

xxx.xxx.xxx.xxx, (i.e. 198.163.2.57).

18. In TCPPort box, type "3001" and click OK.

19. In the RDCfg dialog box, click Save.

20. A Config Info window appears with the mes-

sage: "Saved service information"; click

OK.

21. Click Close.

22. Restart the computer.

3.7.

Set up Redirected COM Port

in UltraSite

Start UltraSite by selecting Start|Pro-

grams|Energy Management|UltraSite32.

From the top menu select System|Setup

Ports|Direct Connect Ports. The redirected

COM port should appear in the Port List.

Select the redirected COM port, (i.e. COM3)

and click Setup.

The Setup Direct Connect Port window

will pop up; click OK.

Click Close in the Direct Connect Ports

window.

Select either Add Site to create a new site, or

Edit Communications Information on the

existing site--both are accessed by right-

clicking on the respective site.

The Edit Site window appears. Select RE-

026-1607 Rev 2 4-04-01