Dell PowerVault MD3060e Series Impostazione

Sfoglia online o scarica il pdf Impostazione per Immagazzinamento Dell PowerVault MD3060e Series. Dell PowerVault MD3060e Series 2. Storage enclosure
Anche per Dell PowerVault MD3060e Series: Manuale hardware e software (25 pagine), Manuale di installazione (11 pagine), Manuale introduttivo (10 pagine), Aggiornamento delle informazioni (8 pagine), Istruzioni per l'installazione del rack (2 pagine), Impostazione (2 pagine), Manuale d'uso (24 pagine), Manuale dell'amministratore (35 pagine), Manuale introduttivo (10 pagine), Manuale d'uso (24 pagine), Manuale d'uso (40 pagine), Manuale dell'amministratore (48 pagine)

Stampa la pagina

Dell PowerVault MD3060e Series Impostazione

Setting Up Your Dell PowerVault MD3060e Storage Enclosure

Racking Your Storage Enclosure

Notes, Cautions, and Warnings

NOTE

indicates important information that helps you make better use of your

system.

CAUTION:

indicates either potential damage to hardware or loss of data and tells

you how to avoid the problem.

WARNING

indicates a potential for property damage, personal injury, or death.

WARNING: Before you set up and operate your Dell PowerVault system, review the

safety instructions that shipped with your system.

Verify Storage Array Components

Your system is shipped with enclosure management modules, power supplies, and fan

components already installed in the enclosure. Make sure that all components are

properly seated and are not dislodged and/or damaged during shipping.

Install the Enclosure in a Rack

The storage enclosure requires a compatible rack and a rack installation kit. For information

about installing the rails for the storage enclosure, see the rack installation instructions that

shipped with your enclosure.

WARNING: Do not plug the enclosure into a standard power outlet. Your storage

array is shipped with two IEC C19 to C20 jumper cords. Plug the C19 plug into the

array's power supplies and the C20 plug into the power distribution unit (PDU) in

the rack cabinet. For power redundancy, split the power connections from each

enclosure into separate PDUs and connect the PDUs to external power receptacles

on different circuits. The enclosure supports only 200 V to 240 V input sources.

Physical-Disk Drawers

The MD Series Dense storage enclosure contains five physical-disk drawers accessible

from the front of the enclosure. Each drawer holds up to 12 physical disks.

To open a drawer:

Flip both latches outward.

Pull the drawer out.

NOTE: When a drawer is opened, the enclosure cooling fan RPM increases

significantly to ensure optimal airflow. This is normal and does not indicate

a problem.

CAUTION:

If a drawer is not completely inserted into the enclosure, other drawers

will be locked. Do not force a drawer open as it may damage the physical disk or the

drawer itself.

To close a drawer:

Push the drawer into the enclosure until the release latch clicks into place.

Close the latches on each side of the drawer.

NOTE: Ensure that the drawer is pushed in and closed completely.

WARNING: Do not install physical disks in the enclosure before installing the

enclosure in the rack. This adds substantial weight to the enclosure and makes lifting

and installing the enclosure in the rack unsafe. For more information, see the rack

installation instructions shipped with your enclosure.

Locate Your System Service Tag

Your system is identified by a unique Express Service Code and Service Tag.

This information is used by Dell to route support calls to the appropriate personnel.

Physical-Disk Carriers

Physical disks are preinstalled in their carriers and shipped separately in anti-static

packaging. For information on installing and removing the physical disks from the

physical-disk carriers, see Dell PowerVault MD3060e Owner's Manual at

dell.com/powervaultmanuals.

Physical Disk Installation Guidelines

•

To maintain proper airflow, install physicals disks from left to right and front to back in

each drawer.

•

A minimum of four disks must be installed in each drawer, filling slots 0, 3, 6, and 9

respectively.

•

Keep all drawers closed unless you need to access the physical disks. The storage array

operates normally with a drawer open, but it is designed for optimal cooling with all

drawers closed.

About the Storage Enclosure

The MD3060e Dense storage enclosure is a five-drawer, 60-physical disk chassis (4U)

managed by two enclosure management modules (EMMs).

Fan Modules (2)

Power Supplies (2)

Enclosure Management Modules (2)

Enclosure Management Modules

Each storage enclosure must contain two EMMs.

Enclosure Management Module

Installing Physical Disks

To install a physical disk into a drawer:

Open the physical-disk drawer.

Rotate the physical disk carrier handle upward to the vertical position.

Align the two raised buttons on the disk carrier with the notches on the

physical-disk drawer.

CAUTION:

Do not install disks randomly. Fill disk slots 0, 3, 6, and 9 first.

Lower the physical disk into the drawer slot.

Rotate the physical disk carrier handle downward until the physical disk is properly

seated in the connector and the physical-disk carrier handle snaps into place.

CAUTION:

Check that the disk is not raised up at the back of the drawer slot,

which would indicate that it is not properly seated. Closing the drawer with an

improperly seated disk will damage both the drawer and the physical disk.

Close the physical-disk drawer.

WARNING: Do not plug the enclosure into a standard power outlet.

Your storage array is shipped with two IEC C19 to C20 jumper cords. Plug the

C19 plug into the array's power supplies and the C20 plug into the power

distribution unit (PDU) in the rack cabinet. For power redundancy, split the

power connections from each enclosure into separate PDUs and connect

the PDUs to external power receptacles on different circuits. The enclosure

supports only 200 V to 240 V input sources.

Follow these steps to power on your storage array:

Turn on any network switches, routers, or other standalone components.

Power on the MD3060e storage enclosure.

NOTE:

Wait for the enclosure status LED to turn blue before proceeding to the

next step.

Power on the attached MD Series Dense storage array or server.

NOTE:

Wait for the storage array status LED to turn blue before attempting to

discover or manage the array.

4 4

1. physical disk

2. physical-disk carrier handle

3. notches on physical-disk drawers

4. buttons on disk carrier

5. drawer latches (2)