EarthQuake T1000W/2 Manuale d'uso - Pagina 8

Sfoglia online o scarica il pdf Manuale d'uso per Amplificatore EarthQuake T1000W/2. EarthQuake T1000W/2 8. Earthquake ph10000w/d1: product brochure
Anche per EarthQuake T1000W/2: Opuscolo (8 pagine)

Stampa la pagina

TD5X

SUB INPUT:

SUB XOVER:

MODE SELECTOR:

This is your

The

0-18dB/Oct

This feature tells the

s u b w o o f e r

Xover provides

amplifier to run in

channel where

control over the

either HIGH PASS,

the sub RCA

device cutoff

FULL RANGE or

outputs from

frequency.

LOW PASS MODE

your head unit

are inserted.

SUBWOOFER CONTROL

GAIN

XOVER

REMOTE

MIN

160

MAX

INPUT SELECTOR

MONO CHANNEL 5 SIGNAL FLOW

LEVEL ADJUST:

REMOTE

INPUT SELECTOR:

Allows the amplifier to deliver a

SUB

This tells the amp to play all channels even if only one pair of

LEVEL:

controlled maximum sound

RCAs is connected. EXAMPLE: If the head unit only has one

level into selected channel(s)

Allows you to

pair of RCA outputs then you must plug them into the CH1/2

adjust

amps

when the volume is turned to

connections and set the switch to 2. This tells the amp that you

max. This acts as a volume

bass output

are using one set of RCAs and it needs to play all five channels

l i m i t e r f o r t h e s y s t e m ,

i n t e n s i t y

regardless. If you have four RCAs, then set it to 4 and so on.

preventing you from over

remotely.

driving the speakers or

subwoofers.

The gain knob is not a volume control.

It is designed to match the input level of

the amp to the output level of the source

unit. Over driving "clipping" the input

stage of the amp will cause damage to the

amplifier (please refer to table for setting).

Three

25A

fuses

GND

REMOTE

+12V

POWER

To car chassis / ground

POWER (PWR) LED:

When LED is on, it indicates that the

amplifier is ON and functioning properly.

To remote turn on / trigger

To battery positive (+)

Specifications Are Subject To Change Without Notice

This information applies to

both channels 1/2 and 3/4

LEVEL ADJUST:

VARIABLE XOVER:

Control the max output of

C o n t r o l

t h e

each channel. The LEVEL

corresponding channels'

controls its respective

cutoff frequencies. This

channel regardless how

feature is disabled when

in FULL RANGE.

many inputs in use.

CHANNEL 1/2 CONTROL

CHANNEL 3/4 CONTROL

MODE

GAIN

XOVER

MODE

GAIN

XOVER

MIN

400

MIN

400

MAX

AUTO ON

RESET

REMOTE ON

5 4 2

CHANNEL 1/2 SIGNAL FLOW

CHANNEL 3/4 SIGNAL FLOW

SUB

XOVER

SETTING

TD5X

40Hz

100Hz 180Hz

280Hz

MAX INPUT

VOLTAGE

BEFORE

CLIPPING

RCA LEVEL

7.0V

4.0V

2.5V

PROTECTION (PROT) LED:

If LED comes on then you have an issue that requires

service. Turn off the amplifier and call Earthquake for

further assistance. See warranty for details.

FRONT

REAR

SUB

FUSES

CH1-

CH2+

CH3-

CH4+

CH1+

CH2-

CH3+

CH4-

PROT

PWR

25A

CH1+

CH2-

CH3+

CH4-

BRIDGED

OUTPUT

Bridgeable speaker outputs,

minimum 4-Ohms, plus

subwoofer connection.

LOW INPUTS:

These are CH1/2

(FRONT)

& 3/4

low inputs

(REAR)

with a range of 0.2V to

7V RMS. This is where

the front and rear RCA

outputs from your head

unit are inserted.

AUTO SIGNAL

SENSING:

Please refer to

p a g e

f o r

explanation of this

feature.

360Hz

400Hz

Set Xover to desired setting and set Mode

switch to HIGH (high-pass). Level

adjustment should be dialed in by ear. Keep

it at MIN and slowly work your way up.

FC6.2

Tweeter

FC6.2 Mid-Range

FC6.2 Xover

FRONT

REAR

SUB

CH1-

CH2+

CH3-

CH4+

CH1+

CH2-

CH3+

CH4-

CH1-

CH2+

CH3-

CH4+

CH5-

CH1+

CH2-

CH3+

CH4-

CH5+

CH1+

CH2-

CH3+

CH4-

BRIDGED

OUTPUT

Focus EQ-693

Set Xover switch to FULL (full range)

www.earthquakesound.com

CH1/2

MIN

MAX

40Hz

400Hz

HIGH

FULL LOW

XOVER

LEVEL

The Sub Channel Will Accept

2 or 4-Ohm Subwoofers

CH3/4

40Hz

400Hz

MIN

MAX

HIGH

FULL LOW

XOVER

LEVEL