32 Degrees PT Jr. Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Attrezzatura per paintball 32 Degrees PT Jr.. 32 Degrees PT Jr. 6. Paintball marker

Stampa la pagina

Welcome . . .

Thank you, for purchasing this PT Jr. Paintball marker. The PT Jr.

represents the culmination of a great deal of research by 32 Degrees along with input

from players such as you. We believe that the affordability of a reliable, feature packed

marker will improve your playing experience and winning percentage. While winning isn't

everything, it sure beats the alternative!

Play Hard, play safe, play to win!

WARRANTY INFORMATION

Standard Warranty:

The manufacturer warranties to the original customer that this product is free from

defects in material and workmanship under normal use and service for a period of 90

days from the original date of purchase by the initial owner/purchaser. The manufactur-

er agrees to repair or replace (at its discretion) any product within a reasonable period

of time. This warranty does not cover: o-rings, scratches, nicks, normal wear and tear of

parts, any modifications or normal fading of anodizing or damage caused by dropping or

hitting of the product. This warranty shall not apply if it is shown by the manufacturer that

the consumer caused the defect or malfunction because of misuse. This warranty only

covers original factory parts. Any modifications or tampering of original factory parts will

not be covered by this warranty. Warranty work can only be conducted by the manufac-

ture technicians and or authorized technicians. If product needs to be repaired, package

it carefully and send it together with your name, address, phone number and a brief

description of the malfunction to:

Paintball Solutions

570 Mantua Blvd

Sewell, NJ 08080

Extended Warranty:

By returning the enclosed warranty registration card or registering your warranty on-line

at www.PaintballSolutions.com, within fifteen days of purchase the warranty will auto-

matically be extended for an additional year.

P A I N T B A L L M A R K E R

Numbers shown in parentheses following part names correspond to the

numbers on the Parts key located on the centerfold pages of this manual.

Initial Assembly

1. Screw the Velocity Adjuster (#4) into the Hammer Plug (#35) approximately two

complete turns.

2. Place a Barrel Plug into the end of the barrel. The barrel is the top chamber of the

Main Body (#23).

3. Push the safety (#25) into the "safe" position (pushing from left to right looking down

the sights).

Attaching Propellant Source

1. Confirm that the Barrel Plug is properly installed and the marker is on "Safe".

2. Cock the marker by pulling the Bolt (#14) in the rearward direction until it "clicks"

into place. This compresses the Main Spring (#2) and allows the Cupseal (#8) to

properly seat.

3. Point the marker downward and in a safe direction.

4. Unscrew the 12 Gram Plug (#19) from the front of the PT JR.

5. Place a few drops of non-corrosive lubricant made specifically for use in paintball

(Empire Oil) into the center of the bottom chamber of the Main Body (#23), where

the CO2 will be punctured. This must be done for every 12 Gram CO

marker. This will run the oil through the valve to ensure the puncture O-Rings stay

moist and do not dry or crack. Failure to do so will cause the marker to leak.

6. Remove the pin from the front of the 12 Gram Plug (#19) by just pulling back on the

ball on the end until it releases.

7. Place the 12 Gram CO

cylinder into the tube with the narrow end in first.

8. Screw back in the 12 Gram Plug (#19) clockwise into the front end of the PT JR.

When almost closed by hand tightening, use the pin in the spaces provided in the

12 Gram Plug (#19) and use it to tighten the 12 Gram Plug into place. *NOTE*

Once sealed, DO NOT OVERTIGHTEN.

Attaching Feed Tube

1. Confirm that the Barrel Plug is properly installed on the marker and is on "Safe".

2. Taking the feed tube hook on the back retaining stud on the body of the PT JR

(#23). Pulling back the front retaining stud clip into place. See Diagram below.

Installing the feed tube:

1. Hook retaining stud

2. Pull back retaining stud

and clip into place.

put into the

Removing the feed tube:

1. Pull back retaining

stud and un-clip from

the seat