EarthWay 2170 Manuale di istruzioni per l'uso

Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Spreader EarthWay 2170. EarthWay 2170 8. Commercial broadcast spreader with side spread control
Anche per EarthWay 2170: Manuale di montaggio e istruzioni per l'uso (6 pagine), Manuale di montaggio e istruzioni per l'uso (8 pagine), Manuale di istruzioni per il montaggio (12 pagine), Manuale di montaggio e istruzioni per l'uso (6 pagine), Manuale di istruzioni per il montaggio (10 pagine)

EarthWay 2170 Manuale di istruzioni per l'uso
2170 Commercial
Broadcast Spreader
ASSEMBLY and OPERATING INSTRUCTIONS
PLEASE CONTACT US IF YOU ARE MISSING ANY PARTS, HAVE ANY DIFFICULTY IN ASSEMBLY, OR HAVE ANY
QUESTIONS REGARDING THE SAFE OPERATION OF THIS SPREADER. THIS MODEL INCLUDES LIFETIME
TECHNICAL SUPPORT. HOT LINE: 574-848-7491 OR 800-294-0671, EMAIL: [email protected]
HELPFUL HINTS:
; If your spreader does not spread evenly, be sure the FRONT on the gear box points to the front of the spreader.
The impeller must turn clockwise. Reversing the gearbox will cause the impeller to turn counter clockwise.
Clean the impeller plate after each use. Fertilizer stuck on the impeller blades will cause uneven spreading.
; Your spreader is designed to be pushed at three miles per hour, which is a brisk walking speed. Slower or
faster speeds will change the spread patterns. Wet fertilizer will also change the spread pattern and flow rate.
Clean and dry your spreader thoroughly after each use. Coat all metal surfaces (pay special attention to the
inside & outside of tubing - it's easiest to do while assembling) with light oil, Fluid Film
to help prevent corrosion. Wash between the shut off plate and bottom of the hopper. Do not use powdered
materials.
; Gears are permanently lubricated at the factory. Do not open the gearbox or dirt may enter.
32100
33117
Qty 2
Qty 1
36210
Qty 2
36214
31100
Qty 4
Qty 4
12152
12148
Qty 2
Qty 2
1. Remove and identify all loose parts from carton
(Qty 4 #36300)
1/4-20 SS Locknut
(Qty 4 #36214)
1/4-20 X 1½"
Phillips Panhead
READ THE DIRECTIONS BEFORE ASSEMBLY
36300
32103
Qty 6
Qty 8
33108
Qty 1
33109
Qty 1
31120
Qty 4
31106
Qty 2
.
Download the
NEW Rate Setting
App in the Apple
and Android App
2. Position hopper on side. Install frame using (4) 1/4-20 x 1-1/2" Pan Head Phillips
bolts and (4) 1/4-20 nylon insert locknuts. First put bolts through holes in frame
then through holes in bottom of hopper. Secure with locknuts. TIGHTEN THESE
LOCKNUTS NOW - DO NOT TIGHTEN WITH POWER TOOLS. TIP: coat stainless
steel bolts with wax or grease before tightening to prevent them from seizing.
ADVERTENCIA
Este producto puede contener un
componente químico conocida en el Estado
de California como causante de áncer,
defectos de nacimiento y otros daños al
sistema reproductor.
www.P65Warnings.ca.gov
with SSC
ROCK SALT and POWDERED MATERIALS should not
be used in this spreader as it will damage gearbox and
can void warranty. Use only granular materials.
16
Stores!
WARNING
This product may contain a chemical known
to the State of California to cause Cancer, or
Birth Defects, or Other Reproductive Harm.
www.P65Warnings.ca.gov
®
13
24
17
9
29
25
26
14
31
7-2018 Pt# 52164
or silicon spray
23
12
11
28
PAGE 1