Allo RemoteControl NICE HSCU2C Manuale di istruzioni - Pagina 2
Sfoglia online o scarica il pdf Manuale di istruzioni per Telecomando Allo RemoteControl NICE HSCU2C. Allo RemoteControl NICE HSCU2C 8.
Stampa la pagina
Installation:
All control panel models are fitted with system memory boards.
During programming, the card stores the system parameters (excluding voice messages recorded
by the installer or user) and can be transferred from one control panel to another. Before
removing or inserting the board make sure that the control panel is off and not powered. Some
control panel models (models HSCU2GC and HSCU2G) are equipped with a GSM telephone dialler.
The SIM card must be inserted before starting installation and with the power off. The SIM card
may be provided by any cellular operator and with any contract (the system only uses the voice
and SMS services), but must be configured with PIN code = "1234" or set as "access without PIN":
this can be done by inserting the SIM card in any GSM phone.
Caution! – For HSCU2GC and HSCU2GW: do not crush or bend the GSM antenna cable
01. Open the container, and remove the protective mask (fig. 7-A) and then the cover (fig. 7-B);
02. Release the side hook to rotate the control panel's: see fig. 8 per mod. HSCU2C and HSCU2W -
see fig. 8A for mod. HSCU2GC and HSCU2GW;
03. Ensure that the memory board is correctly inserted in the internal connector guides (fig. 9). In
control panel models HSCU2GC and HSCU2G (with GSM), also insert the SIM card (fig. 10);
Visit our website: www.Alloremotecontrol.com
04. Before securing the container, you can activate the blade proofing system on the rear tamper
(fig. 11): a) remove part "a" as shown and set it aside b) remove part "b" as shown and discard it;
05. For models HSCU2GC and HSCU2C: set up the cable hole (fig. 12) and run the power cables
through it (fig. 13);
06. Restore the control panel body to its holder (fig. 14);
07. Mark on the wall the 3 mounting points indicated in fig. 15 and the bladeproofing system hole
indicated as detail "a" (fig. 15);
08. Drill the wall at the 3 marked points and insert the provided wall plugs (fig. 16). For the blade-
proofing system, drill the 4th hole and fit the anchor plug and part "a" previously set aside (fig.
16);
09. Fix the control panel to the wall with the provided screws (fig. 17);
10. Electrical connections: • For models HSCU2GC and HSCU2C: make the electrical connections
and insert the backup battery with reference to chapter 5. • For models HSCU2W and HSCU2GW:
connect the battery (battery pack) as shown in fig. 18;
11. Close the container (fig. 19);
12. Now install the various devices and program the control panel
ELECTRICAL CONNECTIONS:
The mains power hookup must be done by a qualified electrician in line with electrical equipment
regulations.
Control panel connections (models HSCU2GC and HSCU2C only)
Caution! – Before opening the control panel's enclosure, disconnect it from the mains power
supply.
01. To hook up the power cable, insert the ferrite cylinder as shown in fig. 20 and position it as
shown in fig. 21; Warnings: - To facilitate the connections to the terminal clamps, depress the
release button. - The wires must be secured by closing the terminal cover with its screw;
02. For the electrical connections to the terminal block, refer to Table 4;
03. To insert the backup battery (not included) refer to fig. 22; 04. Once the connections have
been completed, close the internal cover and only then close the circuit breaker or insert the mains
plug
Visit our website: www.Alloremotecontrol.com