Dialogic Brooktrout TR1034 BRI Manuale di installazione

Sfoglia online o scarica il pdf Manuale di installazione per PCI Card Dialogic Brooktrout TR1034 BRI. Dialogic Brooktrout TR1034 BRI 2. Pci fax board
Anche per Dialogic Brooktrout TR1034 BRI: Manuale di installazione (2 pagine)

Stampa la pagina

Installing the Dialogic®

Brooktrout® TR1034 BRI

PCI Express Board

Part Number: 931-162-06

TR1034

The Dialogic® Brooktrout®

Basic Rate

Interface ISDN PCI Express board ("TR1034 BRI

board" or "board") is half-sized, single-slot PCI

Express-bus compatible fax and voice processing

board. It provides the following:

On-board BRI connections

V.34 (33.6 Kbps) fax transmission speeds

Up to four fax and voice channels per board

The TR1034 BRI PCI Express Series board is a single

lane (x4 form factor) cards.

You need a fax or voice application to use a

TR1034 BRI board should you choose to do so.

Dialogic does not provide the application or a driver

for this board. A driver comes with the application

that you purchase.

This installation guide provides information about:

System Requirements (including telephone

service)

Setting the Module Number

Setting Termination Jumpers for the BRI Line

Installing a Dialogic® Brooktrout® TR1034 BRI

Board

Recognizing PCIe Slots

Connecting the Phone Service

Understanding LED Signals

Using a Dialogic® Brooktrout® TR1034 BRI

Board

Getting Help

System Requirements

This board must be installed in an enclosure that

meets the following specifications:

Chassis Requirement: Compliant to the PCI

Express Base Specification, Rev 1.0a

A Pentium or later host processor

Recognizing

A PCIe x4, x8, or x16 bus slot. See

PCIe Slots

for more information.

Temperature: 0 C - 50 C

Humidity: 10% - 95% (non-condensing)

Power Requirement (Maximum Load)::

Board

+ 3.3 V

+ 12 V

Total Power

Single Channel

1.1 A

0.A

3.63 W

Dual Channel

1.2 A

0.A

3.96 W

The following is also required:

Telephone service: BRI interface

Options are provided for one or two BRI (2B+D) S/T

interfaces with B and D-channel HDLC support.

Compliant with I.430 ITU S/T ISDN support in

Terminal Equipment (TE) and network terminator

(NT) mode.

Setting the Module Number

Set each board to a unique module number to easily

identify the resources associated with a specific board

in a multi-board system.

Use the SW-1 rotary switch (Figure 1) to set a unique

module number for each Dialogic® Brooktrout®

board. See Figure 5 for the switch location. Select a

number from 2 - F on the rotary switch. Settings 0 and

1 are reserved and cannot be used.

Figure 1. Rotary Switch (SW-1)

Setting Termination Jumpers

for the BRI Line

Before installing your board, set termination for the

BRI line if necessary. See Figure 5 for the location of

the termination switches.

Set jumpers as follows (See Figure 2 for details):

Jumper is removed

Jumper is in place

(ISDN BRI line is not terminated)

(ISDN BRI line is terminated)

Figure 2. Termination Jumpers

When the jumpers are removed from both

switches for the appropriate port, there is no

termination.

When jumpers are present, the lines are

terminated with 100 ohms (this is how the board

is shipped).

Dialogic does not support any configuration

except the two illustrated in Figure 2.

Installing a Dialogic

Brooktrout

TR1034 BRI Board

To install your board:

Turn off your PC and remove the cover.

Caution: A small amount of static electricity can

destroy the sensitive components on your board.

To prevent static damage, always connect yourself

to ground using a ground strap before touching a

circuit board. Handle the boards only by the edges

or metal mounting brackets and transport boards

in an anti-static bag.

If the system has a PCIe expansion hold-down

bar, remove it.

Locate a free PCI Express bus slot that is x4 or

larger.

Align the board with the slot and firmly seat the

board into the slot. Carefully insert the PCI

Express Board Edge Connector into the PCI

Express Slot to avoid damage to the board.

Tighten the mounting bracket screw to secure the

board to the chassis.

Warning: When installing the board, be sure that

the mounting bracket is securely fastened to the

chassis and the chassis is plugged into a

grounded three prong plug. Improper chassis or

bracket grounding can result in harmful or fatal

electrical shock as well as component damage.

Replace the cover.

Turn on your computer.

Dialogic® Brooktrout® boards should not be present in the

Note:

computer during the installation of any operating system.

The operating system might misinterpret the board as being

some other device, with unpredictable consequences.

Recognizing PCIe Slots

The PCIe connectors in the computer chassis usually

appear as white slots. The TR1034 BRI board has a

PCI board edge connector. It can be inserted into any

of the PCIe slots shown in Figure 3.

Figure 3. PCIe Slots

Connecting the Phone Service

You must install the appropriate telephone service and

hookups at your site to connect to telephone service.

The following table shows the channel/port

relationship:

Channel

Type of

RJ-45 Port

Number

Service

BRI S/T

To ensure

Use the cable supplied with the board.

conformity, shielded cables must be used.

Do the following to connect your board to BRI

service:

Plug one end of the cable into the telephone

connector on the board.

Connect to Port A for channels 0 and 1 or to

Port B for channels 2 and 3 (see Figure 5 to

locate ports).

Plug the other end into the wall connector for

your BRI service.

Port B is not present on the TR1034 BRI single port version.

Note: