Dialogic DM/F300-1E1-PCIU Scheda di installazione rapida - Pagina 2

Sfoglia online o scarica il pdf Scheda di installazione rapida per Hardware di rete Dialogic DM/F300-1E1-PCIU. Dialogic DM/F300-1E1-PCIU 2. Dm3 fax boards

Stampa la pagina

5. Using the slot's board guides, insert the edge

connector of the board into the bus slot. Press firmly

until the board is securely seated in the slot.

Installing a PCI Board

Remove

Cover

Plate

Computer

Chassis

PCI Slot

ISA Slot

6. Replace and tighten the retaining screw to secure the

board firmly in the chassis slot (if applicable).

7. Connect external digital telephone cable to the

RJ-48C jack on the board bracket.

RJ–48C Connectors

Pinouts for the RJ–48C

Network Interface

Jacks on Bracket

Cable Connector

RCV_RING

Pin 1

RCV_TIP

CHASSIS GROUND

XMIT_RING

XMIT_TIP

CHASSIS GROUND

8. Repeat steps 3-7 for each additional board you are

installing.

9. Use the CT Bus cable to connect the board(s) you

are installing to other boards in the system. To

preserve the electrical integrity of the CT Bus, use a

CT Bus cable with the appropriate number of

connectors ("drops"). It is recommended that no more

than two connectors at either end of the cable be left

unused.

Installing the CT Bus Cable

Colored

Stripe

(Pin 1)

NOTE:

Your CT Bus cable may

have a different number

of connectors (drops).

Note: Your system may include both CT Bus and SCbus

boards. To connect both board types, you must install a

CT Bus/SCbus Adapter on one of the CT Bus boards in a

system. See the CT Bus/SCbus Adapter Quick Install

Card for installation details about the Adapter and the

bus cables.

10. Install CT Bus Termination Jumpers only on boards

PCI

located at each end of the CT Bus cable. See the

Board

"Physical Description" section for jumper details.

11. Replace the computer cover when finished and

reconnect the power cord.

12. Turn the computer's power on.

CAUTION: If your BIOS is set to use Plug and Play

technology and there are ISA boards in your system, an

IRQ conflict can be created if a PCI Dialogic telecom

board is assigned the same IRQ as an ISA board. This

could cause the machine to stop responding. You can

prevent this by entering the BIOS and reserving the

appropriate IRQs (those used by your ISA boards) for

ISA use only.

After Installing the Hardware

Note: If you are adding hardware to an existing system,

you do not need to uninstall existing Dialogic

Software.

For a new installation, after installing the hardware

proceed with the system software installation as

described in the Dialogic System Software

documentation.

For technical specifications and product information go

to: http://www.dialogic.com/products.htm.

Warranty and Return Information

For specific warranty information for this board, refer to

the Warranty section of the Products page, located at

this URL: http://www.dialogic.com/warranties/.

Contacting Technical Support

Dialogic provides technical support for its products

CT Bus

Cable

through a network of value added distributors who are

trained to answer technical questions on installing and

configuring Dialogic

contact your support channel, please call Dialogic in the

United States at 973-967-6600 (9am-5pm EST) and we

will assist in obtaining the appropriate support channel.

Outside the United States please refer to

http://www.dialogic.com/support/contact

System

Warranty Period

products. If you are unsure how to

to obtain

local contact information. Dialogic also provides direct

support via Dialogic

Pro™ Services agreements. For

more details of direct support from Dialogic please refer

to: http://www.dialogic.com/support/DialogicPro.

Returning a Product

To return a board for warranty repair or any other

returns, please refer to the following:

http://www.dialogic.com/support/hwfaults.

Sales Assistance

If you have a sales question, please contact your

local Sales Representative or the Regional Sales Office

for your area. Address, telephone and fax numbers, are

available at the Dialogic website located at:

http://www.dialogic.com/contact.htm.

To purchase Dialogic

products, please refer to the

following website to locate the appropriate supplier:

http://www.dialogic.com/purchase.htm.

All contents of this document are furnished for informational use only and are subject to change without notice

and do not represent a commitment on the part of Dialogic Corporation or its subsidiaries ("Dialogic").

Reasonable effort is made to ensure the accuracy of the information contained in the document. However,

Dialogic does not warrant the accuracy of this information and cannot accept responsibility for errors,

inaccuracies or omissions that may be contained in this document.

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIALOGIC

NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL

PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED

AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER,

AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR

USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS

FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL

PROPERTY RIGHT OF A THIRD PARTY.

Dialogic products are not intended for use in medical, life saving, life sustaining, critical control or safety

systems, or in nuclear facility applications.

It is possible that the use or implementation of any one of the concepts, applications, or ideas described in this

document, in marketing collateral produced by or on web pages maintained by Dialogic may infringe one or more

patents or other intellectual property rights owned by third parties. Dialogic does not provide any intellectual

property licenses with the sale of Dialogic products other than a license to use such product in accordance with

intellectual property owned or validly licensed by Dialogic and no such licenses are provided except pursuant to a

signed agreement with Dialogic. More detailed information about such intellectual property is available from

Dialogic's legal department at 9800 Cavendish Blvd., 5

Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic

encourages all users of its products to procure all necessary intellectual property licenses required to

implement any concepts or applications and does not condone or encourage any intellectual property

infringement and disclaims any responsibility related thereto. These intellectual property licenses may

differ from country to country and it is the responsibility of those who develop the concepts or applications

to be aware of and comply with different national license requirements.

Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and SIPcontrol, among others, are either

registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used publicly only with permission

from Dialogic. Such permission may only be granted by Dialogic's legal department at 9800 Cavendish Blvd., 5th

Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized use of Dialogic's trademarks will be subject to full

respect of the trademark guidelines published by Dialogic from time to time and any use of Dialogic's trademarks

requires proper acknowledgement. The names of actual companies and products mentioned herein are the

trademarks of their respective owners.

PRODUCTS.