Dialogic Switching Board DI0408LSAR2 Scheda di installazione rapida

Sfoglia online o scarica il pdf Scheda di installazione rapida per Hardware di rete Dialogic Switching Board DI0408LSAR2. Dialogic Switching Board DI0408LSAR2 2. Switching board

Stampa la pagina
Dialogic
®
DI0408LSAR2
Switching Board
Quick Install Card for Universal PCI
Part number 64-0039-02
Copyright © 2002-2007
Dialogic Corporation.
All Rights Reserved..

Before You Begin

Protecting the Board from Damage
Caution!
All computer boards are sensitive
to electrostatic discharge ("ESD"). Handle all
static-sensitive boards and components at a static-
safe work area, and observe anti-static precautions
at all times.
If you are not familiar with ESD safety precautions, visit
http://www.dialogic.com/support/hwinstall to learn more.
Unpacking the Board
®
Unpack the Dialogic
DI0408LSAR2 Switching Board
("board") according to the following steps:
1.
Prepare a static-safeguarded work area.
2.
Carefully remove the board from the shipping
carton and anti-static packaging. Handle the
board by the edges and avoid touching the
board's components.
3.
Lay the board on the static-dissipative work
surface.
Note: Place boards in static-shielding bags when carrying
boards from station to station.
CAUTION: Do not remove the board from the anti-static
packaging until you are ready to install it. Observe proper
anti-static precautions at all times.
CT Bus connector
1.
Physical Description
2.
Green LED - Power On
3.
Yellow LED - User Defined #1 and #2
Red LED - Out of Service
4.
1
Switch SW100 - For future use
5.
5
2
3
4
Pinouts for the
RJ61X Jack
8
7
6
5
4
3
2
1
8
8 RING 4
7 RING 3
6.
Power supply connector - Connects
6 RING 2
to external power supply
5 RING 1
7.
RJ61X jacks - Connects to telephone
4 TIP 1
breakout box
3 TIP 2
8.
Universal PCI bus connector
2 TIP 3
9.
Audio Input Jack for music on hold
1 TIP 4
feature
NOTE: The figure shows a North American-compliant power supply cord for connecting to AC power. Use the appropriate power supply cord for your location.

Hardware Configuration

The device driver, part of the system software,
assigns board identification (ID) numbers in
ascending order (beginning with 0) as it detects each
board in the system. The board identification
number is used by the system software to recognize
the board. NOTE: If you add a board to the
system, the existing board ID numbers may change,
depending upon the PCI bus and slot number where
the new board is installed.
Windows System
After the hardware and the system software are
®
installed, refer to the Dialogic
Configuration
Manager (DCM) utility to retrieve the board instance
(ID) number(s) assigned to the board(s) in your
system and see online help for more details.
Pinouts for the
Power Connector
5
6
3
4
1
2
Chassis
Ground
1
PC_SENSE
2
-24/-70 Return
3
-24/-70 Return
4
-24 Volts
5
-70 Return
6
-24 Volts
6
9
7

Install the Hardware

With the computer on the static-safe work area and
your static-dissipative wrist strap connected to you
and the work area, ensure that the power is OFF and
disconnect all power cords from the electrical
outlets.
1. Remove the cover, select an empty PCI bus
slot and remove the slot's retaining screw and
access coverplate.
2. Install the board into the chassis. Press firmly
until the board is securely seated in the slot.
3. Replace and tighten the retaining screw to
secure the board.
4. Replace the computer cover and reconnect the
power cords.
Connect Breakout Box and Power Supply
Power
To
Supply
AC
Power
DI/0408-LS-A-R2
Board
RJ61X
Cables
Set CT Bus Jumpers (optional)
The Computer Telephony bus (CT Bus) provides
communication and flexible resource sharing
among the boards connected to the bus. This
board has a CT Bus connector that complies with
the ECTF H.100 specification, and as such can be
connected to the CT Bus with a CT Bus cable.
You can connect the board to the CT Bus or use it
without the CT Bus in stand-alone mode.
•
Stand-Alone Mode (CT Bus Jumpers Ignored):
For applications that do not require media sharing or
switching across the CT Bus, use the board in stand-
alone mode. No CT Bus cable is required.
In addition, you may skip the instructions in this
section when you use the board in SCbus mode
without a CT Bus master board; that is, using only
SCbus master/slave boards.
•
CT Bus Mode (CT Bus Jumpers Needed):
connect the boards to the CT Bus, set the
RJ-11
Cables
To
Telephone
Extensions
To Trunk
Lines
Breakout
Box
To