Burkert SE36 Manuale - Pagina 2
Sfoglia online o scarica il pdf Manuale per Strumenti di misura Burkert SE36. Burkert SE36 5. Positive displacement flowmeter
Stampa la pagina
S E 3 6 + S 0 7 7
Complete device data
(Sensor-fi tting S077 + transmitter SE36)
Pipe diameter
Thread connection
Flange connection
Measuring range
Viscosity > 5 mPa.s
Viscosity < 5 mPa.s
Medium temperature
with body
in aluminium / in stainless steel
Medium pressure max.
DN15
DN25 / DN40 or DN50
DN80 / DN100
Viscosity
Measurement deviation
2)
Repeatability
Electrical data
Power supply
2 or 3 outputs transmitter
(2-wire)
4 outputs transmitter
(3-wire)
Characteristics of the power
source
of UL recog-
(not provided)
nized devices
Current consumption
with sensor
2 or 3 outputs transmitter
(2-wire)
4 outputs transmitter
(3-wire)
Power consumption
Protection
Output
Transistor
1 transistor output
(transmitter 2-wire)
2 transistor outputs
(transmitter 2 or 3-wire)
Current
1 current output
(transmitter 2-wire)
2 current outputs
)
(transmitter 3-wire
4...20 mA output uncertainty
Standards, directives and certifi cations
Protection class
Standards and directives
Pressure
(Sensor-fi tting S077, DN15...
DN100, in aluminium or stainless steel)
Certifi cation
(only for SE36)
UL-Recognized for
US and Canada
1)
or in accordance to the value of the used fl anges.
* F.S. = Full scale (10 m/s)
2)
= "measurement bias" as defi ned in the standard JCGM 200:2012
If the device is mounted in a humid environment or outside, then the maximum allowed
voltages are 35 V DC instead of 36 V DC.
DN15...DN100
½"; 1"; 1½"; 2"; 3"
(G or NPT)
25; 40; 50; 80 or 100 mm DIN PN16 fl ange
1"; 1½"; 2"; 3" or 4" ANSI 150LB fl ange
2...1200 l/min
(0.53...320 gpm)
3...616 l/min
(0.78...320 gpm)
-20...+80°C
/ -20...+120°C
(-4...+176°F)
55 bar
(798.05 PSI) (threaded process connection)
1)
55 bar
/ 18 bar
(798.05 PSI)
(261.18 PSI)
12 bar
/ 10 bar
(174.12 PSI)
(145.1 PSI)
1 Pa.s max.
(higher on request)
±1% of the measured value
(if "standard" K-factor is used)
±0.5% of the measured value
(if "specifi c" K-factor is used,
on label of the product)
±0.03% of the measured value
14...36 V DC, fi ltered and regulated
12...36 V DC, fi ltered and regulated
Limited power source
(according to § 9.4 of the UL61010-1
or, Class 2 type power source
standard)
1310/1585 and 60950-1 standards)
≤ 1 A
(with transistors load)
≤ 25 mA
(at 14 V DC without transistors load, with current loop)
≤ 5 mA
(at 12 V DC without transistors load, without current loop)
40 W max.
Reversed polarity of DC: protected
Voltage peak: protected
Short circuit: protected for transistor outputs
NPN, open collector, 1...36 V DC, max. 700 mA
Adjustable as sourcing or sinking (
, open collector, max. 700 mA, 0.5 A max. per
or NPN )
transistor if the 2 transistor outputs are wired
NPN-output: 1...36 V DC
PNP-output: Power supply
4...20 mA adjustable as sourcing or sinking
,
mode as transistor)
max. loop impedance: 1100 Ω at 36 V DC ;
610 Ω at 24 V DC; 180 Ω at 14 V DC
max. loop impedance: 1100 W at 36 V DC;
610 Ω at 24 V DC; 100 Ω at 12 V DC
±1%
IP65, IP67 with device wired and M12 cable plug
mounted and tightened and cover fully screwed down
The applied standards, which verify conformity with
the EU Directives, can be found on the EU Type
Examination Certifi cate and/or the EU Declaration of
conformity
(if applicable)
Complying with article 4, §1 of 2014/68/EU directive*
UL61010-1 + CAN/CSA-C22.2 No.61010-1
Materials view
Brass,
nickel plated
Stainless
steel
(-4...+248°F)
PC
(according to the
Stainless steel
respectively both as PNP
(in the same
* For the 2014/68/EU pressure directive, the device
can only be used under the following conditions (de-
pends on max. pressure, pipe diameter and fl uid).
Type of Fluid
Fluid group 1,
article 4, §1.c.i
Fluid group 2,
article 4, §1.c.i
Fluid group 1,
article 4, §1.c.ii
Fluid group 2,
article 4, §1.c.ii
PC
Silicone
PPS
EPDM
Aluminium or
stainless steel
FKM or
FEP/PTFE
Top interior view
PPS,
aluminium or
stainless steel
Conditions
DN ≤ 25
DN ≤ 32 or
PN*DN ≤ 1000
DN ≤ 25 or
PN*DN ≤ 2000
DN ≤ 200 or
PN ≤ 10 or
PN*DN ≤ 5000
2/5