Miller AC 150 Stick Manuale d'uso - Pagina 6

Sfoglia online o scarica il pdf Manuale d'uso per Sistema di saldatura Miller AC 150 Stick. Miller AC 150 Stick 24.

Stampa la pagina

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

WELDING

explosion.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks,

hot workpiece, and hot equipment can cause fires

and burns. Accidental contact of electrode to metal

objects can cause sparks, explosion, overheating,

or fire. Check and be sure the area is safe before

doing any welding.

1. Protect yourself and others from flying sparks and hot metal.

2. Do not weld where flying sparks can strike flammable material.

3. Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

4. Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

1-3. Additional Installation, Operation, And Maintenance Hazards

FIRE OR EXPLOSION can result from

placing

combustible surfaces.

1. Do not install unit on, over, or near combustible

surfaces or flammables.

HOT PARTS can cause severe burns.

1. Do not touch hot parts bare handed. Allow cooling

period before touching welded parts.

1-4. Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American

Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126

Safety and Health Standards, OSHA 29 CFR 1910, from

Superintendent of Documents, U.S. Government Printing Office,

Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for Welding and

Cutting of Containers That Have Held Hazardous Substances,

American Welding Society Standard AWS F4.1, from American

Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

1-5. EMF Information

Considerations About Welding And The Effects Of Low Frequency

Electric And Magnetic Fields

The following is a quotation from the General Conclusions Section of

the U.S. Congress, Office of Technology Assessment, Biological

Effects of Power Frequency Electric & Magnetic Fields – Background

Paper, OTA-BP-E-53 (Washington, DC: U.S. Government Printing

Office, May 1989): ". . . there is now a very large volume of scientific

findings based on experiments at the cellular level and from studies

with animals and people which clearly establish that low frequency

magnetic fields can interact with, and produce changes in, biological

systems. While most of this work is of very high quality, the results are

complex. Current scientific understanding does not yet allow us to

interpret the evidence in a single coherent framework. Even more

frustrating, it does not yet allow us to draw definite conclusions about

questions of possible risk or to offer clear science-based advice on

strategies to minimize or avoid potential risks."

OM-194 415 Page 2

can

cause

fire

unit

on,

over,

1. Protect compressed gas cylinders from excessive heat,

mechanical shocks, slag, open flames, sparks, and arcs.

2. Keep cylinders away from any welding or other electrical circuits.

3. Never drape an electrode holder over a gas cylinder.

4. Never allow a welding electrode to touch any cylinder.

5. Never weld on a pressurized cylinder – explosion will result.

5. Watch for fire, and keep a fire extinguisher nearby.

6. Be aware that welding on a ceiling, floor, bulkhead, or partition

can cause fire on the hidden side.

7. Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

8. Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock and fire hazards.

9. Do not use welder to thaw frozen pipes.

10. Remove stick electrode from holder when not in use.

11. Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

12. Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

MAGNETIC

near

CURRENTS

operation.

1. Wearers should consult their doctor before going

near arc welding, gouging, or spot welding

operations.

FLYING PIECES OF METAL or DIRT can

injure eyes.

1. Wear safety glasses with side shields or face

shield.

National Electrical Code, NFPA Standard 70, from National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from

Canadian Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices For Occupation And Educational Eye And Face

Protection, ANSI Standard Z87.1, from American National Standards

Institute, 1430 Broadway, New York, NY 10018.

Cutting And Welding Processes, NFPA Standard 51B, from National

Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

To reduce magnetic fields in the workplace, use the following

procedures:

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cables around the body.

4. Keep welding power source and cables as far away as

practical.

5. Connect work clamp to workpiece as close to the weld as

possible.

About Pacemakers:

The above procedures are also recommended for pacemaker

wearers. Consult your doctor for complete information.

FIELDS

FROM

HIGH

can

affect

pacemaker