Aquaosmo BT-KM38R Manuale di istruzioni - Pagina 5

Sfoglia online o scarica il pdf Manuale di istruzioni per Distributore d'acqua Aquaosmo BT-KM38R. Aquaosmo BT-KM38R 9. Atmospheric water generator

1. Please make sure all the components inside the package are installed well completely. Lay the product on hard and smooth

ground, with the placing location favorable for air ventilation, keep not less than 20 cm away from the wall and pull down the

brake pulley pole to fix the machine.

When the unit placed on the ground with big angle, this part one connect to the middle of the back of unit , the other side connect

to the wall next with unit which could prevent tilt. At the same time Belt brake foot brake.

Note: The "Z" shaped metal sheet is optional, if customers need, could ask for the distributor when you buy or installation.

2. Allow the machine to acclimate for at least 1 hours before plugging onto any power.

3. The limited load current of sockets and power cords shall be not lower than 15 Amp and electric shock protector shall be

installed and grounded well.

4. For the first time operation, it is suggested to fill up the bottom tank with tap water. Turn on the power switch ON/OFF after

being charged until water flows from the hot water tap, press down the button of cold and hot water with 1 L water discharged

respectively, and at last drain the remaining water from the hot water outlet at the back of the machine.

(II): Operating steps

1. The toot sound can be heard after plugging the attaching plug of the machine, which shows that the machine is on standby.

Press the power switch ON/OFF button, and the LED indicator lights. Press the water producing button COLD, and the

compressor starts to work after 1.5 minutes. The machine also has a power failure memory function, call again after power can

automatically return operation.

2. If the machine does not produce cold or hot water in the first 12 hours, there is no need to worry for the users, because the

heating and refrigeration function of the machine will start only when the water level of the machine reaches the appropriate water

line.

3. Pressing the HOT button can start the heating process when there is sufficient water, and the red teacup mark will light and

blink, and if the heating is completed, the mark will only light but not blink. Pressing HEAT button for 5 second can stop heating in

the heating stage.

4. Pressing the COLD button can start the refrigeration process when there is sufficient water, and the green snowflake mark will

light and blink, and if the refrigeration is completed, the mark will only light but not blink. Pressing COLD button can for 5 second

stop refrigeration in the refrigeration stage.

5. Press ℃/F button can achieve the free switch between the centigrade degree and degree Fahrenheit and can close sound by

pressing for 5 seconds.

6. The cooling and heating can start at the same time. The refrigerated water temperature and the hot water temperature will be

kept within the preset range automatically, and the current water temperature will be indicated.

The preset hot water temperature is 87-92℃; the preset cold water temperature is 6-10℃.

7. When it is necessary to replace the filtration system, the REPLACE FILTER icon on the display screen will blink automatically

to remind the user to replace filter elements (please refer to the part of the filter element replacement in the instruction).

8. The system will enter into defrosting status when the ambient temperature is excessive low.

9. The cold water will flow by pressing "

"button.

10. The water producing speed will drop in the dry and cold season.

(I): Touch key operation instructions:

1. Power switch "ON/OFF": "ON/OFF" can keep the machine on standby or not, and LED screen lights.

2. Water producing and cooling water producing button ""COLD": Press this button to control the cooling system starting and

closing. The icon "

" will light or flicker.

3. Heating water producing button "HOT": Press it to start the function of producing hot water and press it again to stop. The icon

"will light or flicker.

4. Button "SET": Press this button to set the hot water temperature, the cold water temperature and the clock.

5/9