Aquaproducts Above GroundSwimming Pool CleanersResidential Robotic Manuale d'uso - Pagina 6

Sfoglia online o scarica il pdf Manuale d'uso per Aspiratore per piscina Aquaproducts Above GroundSwimming Pool CleanersResidential Robotic. Aquaproducts Above GroundSwimming Pool CleanersResidential Robotic 8. Aboveground swimming pool cleaners residential robotic

Stampa la pagina

OPERATING INSTRUCTIONS

Cleaning

The size of your pool, and the amount of debris in it, will

determine the length of time required to clean the pool. The time

may vary from one to two hours.

When your cleaner slows down considerably or constantly

reverses direction before reaching the sides of the pool, it is

sending a signal that it is time to clean the Filter Bag.

Removing Your Cleaner From The Pool

After two hours, the cleaner has completed cleaning the pool

and will automatically turn itself off.

Turn off the Power Supply by pressing the ON/OFF switch to

the OFF position. Unplug the cleaner's Floating Cable from the

Power Supply, and gently pull the cleaner toward you using the

Floating Cable. When the cleaner is within reach, remove it from

the water using the side-plate handle only, never remove or carry

the cleaner by its Cable! Removing the cleaner by its Floating

Cable may cause severe damage to the cable requiring costly

repairs.

Important:

Always reverse the locking pin position to the

alloted hole on the opposing side of the turning wheel axle

after each use to protect the Floating Cable from twisting.

In-Season Storage

Tilt the cleaner on its side to allow water to drain from its

body. Do not leave your cleaner in the pool when not in use.

Doing so, will reduce the life of your Filter Bag and pool cleaner.

After removing your cleaner from the pool you should clean and

re-install the Filter Bag. Then rest the cleaner in a dry, shaded

area along with its Power Supply and correctly coiled Floating

Cable.

Helpful Tip For Preserving Your Cleaner

We suggest that you rinse your cleaner inside and out after

removing it from your pool to remove the chlorine and preserve

its appearance.

Off-Season Storage

When the Pool Season is over you should thoroughly clean the

Filter Bag, make sure that there is no water in the cleaner,

completely untangle, and then properly coil the Floating Cable.

Your cleaner and Power Supply should be stored in a dry,

sheltered area that does not fall below 32° F/ 0° C.

CLEANING OR CHANGING THE FILTER BAG

When removing the cleaner from the water, make sure that the Power Supply is turned off and that the cleaner's Floating Cable is

unplugged.

Place the cleaner on its back on a soft non-abrasive surface to protect your cleaner from scratches. Using your thumbs, push the two

Lock Tabs away from the center of the cleaner to unlock the Bottom Lid Assembly (FIG. 10). Remove the Bottom Lid Assembly (FIG. 11)

Remove the Filter Bag from the bag support Wire Frames (FIG. 12).

Turn the Filter Bag inside out (the Fine Filter Bag has a soft felt surface on the inside) and wash off visible dirt using a garden hose or a

faucet. Gently agitate the bag in your hands to help remove fine particles. Continue cleaning and squeezing the Bag gently until rinse

water is clear. Use of a washing machine (cold water only) is recommended when visible dirt will not rinse off by other methods. DO

NOT USE DETERGENT or BLEACH! DO NOT MACHINE DRY!

Turn the Filter Bag "right side out" (felt surface on the inside) remount the Bag on the Wire Frames making sure that the Label on the

Bag is centered on one of the long sides of the Bottom Lid Assembly (FIG. 14). Pull the Bag toward the middle of each Wire Frame so

that the

bag corners are snug against the corners of the Wire Frame. Tuck the excess bag into the lower points of the Wire Frames

(FIG. 14).

Re-install the Bottom Lid Assembly. Make sure that neither debris nor the Filter Bag itself interferes with complete closure of the Bottom

Lid Assembly.

For Technical Support Please Call

1-800-845-4856 Or You Can Visit Us On The Web

At www.AquaProducts.com/Service

Bottom Lid Assembly

Filter Bag

Fine Filter Bag Part #8100

Mesh Filter Bag Part #8200*

*Sold Separately