Aquaproducts UltraMAX Junior Manuale dell'operatore - Pagina 4
Sfoglia online o scarica il pdf Manuale dell'operatore per Pulitori per piscine Aquaproducts UltraMAX Junior. Aquaproducts UltraMAX Junior 11. Commercial swimming pool cleaners
Stampa la pagina
Changing Molded Rubber Scrubbing Brushes:
Depending upon how frequently you use your Cleaner, it will be neces-
sary to replace the Brushes (SP3002BM4 or SP3002) when they wear
out. Tired and worn out Brushes will impede Cleaner's scrubbing ability
and overall performance.
1.Remove old Brushes by cutting the long tabs with scissors.
2.Wrap the new Brush around the Wheel Tube (A38200, A38201 or
A38200MG).
3.Carefully pull the long triangular tabs through their corresponding slots.
CAUTION: Gently tug each tab to the left then to the right to make
sure they are all the way through the slits and are secure. Pulling
the tabs straight through the slots may cause them to tear.
If your Cleaner is equipped with PVA Brushes for better performance in
tiled, fiberglass or slippery surfaced pools, call Aqua Products Tech Support
for assistance in changing out worn PVA Brushes;
(888 AQUATECH/278-2832) or e-mail [email protected].
Changing The Drive Belts:
After a number of months or years (depending on usage & pool
chemistry) the Drive Belts (two at each end behind the Side
Plates - SP3400B6H) will stretch. To maintain optimum
performance these will require periodic replacement.
CAUTION: If "shocking" water be sure to remove Cleaner
prior and allow at least 24 hours for dilution before returning
Cleaner to water.
1. Remove Drive Tracks (3200 or 3201).
2.Turn Cleaner upside down and remove Bottom Lid
Assembly.
3. Locate the four Screws (SP3401) on Drive Motor
(A8523SL or A8524BBSL) side, which holds Side Plate in place.
NOTE: Before removing the Screws, notice how the
Drive Belts are positioned for re-assembly.
4. Remove old Belts and replace them, being
careful to properly position the replacement Belts. Each Belt
must be pressed against Stepped Sleeve Roller (3500) for
proper tension.
5. To re assemble, reverse steps 4 through 1.
6. Repeat this entire procedure on the other side of your Cleaner.
Keeping Your Cleaner Clean:
1. Although your Cleaner is made primarily of corrosion resistant materials, a good cleaning of the entire Cleaner with fresh water after
each operating cycle will add years of trouble free operation and extend the life of its wear and tear parts.
2. From time to time, pine needles, string or other foreign materials may lodge themselves around the Propellers (4400) located on top of
the Cleaner. Unplug the Cleaner from the Power Supply. Simply remove the Screws (2260) holding each Outlet Top onto the top of the
Cleaner then gently remove any debris from the Propellers. The Propellers should also be removed for cleaning underneath.
This can be done by pulling the Propeller upward. When reassembling the Outlet Top DO NOT OVERTIGHTEN as it may fracture
Outlet Top area.
Storage Of Your Cleaner:
Do not allow your Cleaner to stay in the pool when not in operation. Chlorine and/or rays will prematurely wear the Cleaner and its
components. Storing your Cleaner on its side or on optional Ultrakart will allow adequate drainage. Keep your Cleaner out of direct sun-
NOTE: Always unplug the Cleaner when not in use.
light when not in use.
Service Your Cleaner:
Your Cleaner uses the newest and most advanced electronic Drive Motors and brushless Pump Motors (A6010U). Should there ever be
a problem with either the Pump or Drive Motors, do not attempt to investigate or repair yourself. Doing so may cause costly damage and
will result in loss of warranty.
Call Aqua Products Technical Service Department at (888-AQUATECH/278-2832) or e-mail [email protected]
No Miracles:
Although your Cleaner is a technically advanced robot, it must be understood that it will not perform miracles... there are just some small
areas of the pool that may not be cleaned. Don't be alarmed if your Cleaner doesn't vacuum dirt that may be trapped in corners, crevices
or hard to reach areas. Simply brush the dirt into an open area and it will be vacuumed by your Cleaner. To maximize the cleanliness of
your pool use the Cleaner on a daily basis. Most large commercial pools that are exceptionally dirty with algae, leaves, etc. may require a
number of cleaning cycles to do the job.