Aquatec PONDMAX EVOII Series Manuale di istruzioni - Pagina 6

Sfoglia online o scarica il pdf Manuale di istruzioni per Pompa dell'acqua Aquatec PONDMAX EVOII Series. Aquatec PONDMAX EVOII Series 13. Submersible water pump

Stampa la pagina

WATERFEATURE PLUMBING GUIDE

If used to supply water to a waterfeature, cascade, waterfall, ect; where a pipe is needed to be used, use the hosetails

supplied in the package.

• For best results, use the bigger tubing size

recommended in the table previously. Depending on

the pump size, select the hose tail requiered for your

tubing size and evaluate whitch step on the hose tail

will be used. If you are using 32mm hose and you

are connecting it to the 32mm\25mm\20mm hose

tail supplied, remember to saw off the smaller size

connection (I.E.: 25mm\20mm step). Otherwise it will

create a unnessary restriction in the plumbing system.

• A omni-directional ball joint is provided for your

convenence when used under water. This is because

the diagonal side sections of the balljoint may seep

water when under pressure. Select the 1 ½" Threaded

Reducing adaptor and screw onto the top of the pump.

To seal adequitly, the use of thread seal tape on this

male thread may be requierd (availible at your local

stockest).

• The fittings pack should include the nessary O'ring

washers. Select the one that will fit the female

connection of the balljoint. Place it firmly in the locking

nut. Now screw the locking nut of the balljoint onto the

Threaded Addaptor on the pump. Fasten firmly but do

not over tighten.

CLEANING INSTRUCTIONS

Begin by ensuring that the mains power supply is disconnected before attempting any maintenance or adjustment of

the unit or the water body. Remove the unit from the water. If your unit is connected to a sponge filter, the filters and

sponges will clog up over time. Please clean regularly (at least once a month) to ensure strong water flow. Failure to

maintain the unit will result in a burnt out motor and other damage.

• All EvoII Submersible pumps are water cooled, if pump

becomes restricted, or blocked, it will overheat and

could cause permanent damage.

• The motor unit of the pump is encapsulated with

epoxy resin and does not need lubrication. Regular

inspections, cleaning and maintenance of impellor is

necessary to ensure longer life. In the centre of the

impellor you may notice a small whole opening that

protrudes through the ceramic shaft from front to back.

It is paramount that this portal is kept unblocked at all

times. This is a cooling channel for the motor.

• If using a fountain kit, take off the fountain set first by

unscrewing it from the top of the pump. Examine the

nozzles to ensure all ports are unblocked. Clean with a

suitable brush if necessary.

• Maintain the filter sponge regularly according to how

long it takes for the sponge to get clogged up. When

the flow starts to be reduced, check and clean if

necessary.

PMAX EVOII 1900_2900_3900_4900 Pump Instructions.indd 6

• Then select the Hose tail. Locate the second O'ring

washer and the locking nut of the hose tail. Slide the

loking nut over the hose tail and insert the second

O'ring in the nut. Then connect the 1 ½" Threaded

Locking Nut on the Hosetail to the Balljoint and screw

in firmly.

• Now connect the tubing to the hose tail. Remember

to use Stainless Stell hose clamps to fasten the hose

on to the hosetail. This is to ensure that the pipe does

not blow off at a later time or leak at this point in the

plumbing system.

• When used in a pond/waterfeature enviroment,

position the pump as outlined above.

• Direct the hose to your desired location.

• To unclip the front filter cage from the front of the

pump, twist the cage in an anti-clockwise direction and

pull forward. See below for diagram. If available, take

out the optional Internal Bio sponge and clean. If using

an optional pre-filter block sponge, slide the sponge

off the threaded core and wash out. It is recommended

that this is done in a bucket of pond water to ensure

the good bacteria that are present in the sponge are

not killed by the Chlorine in tap water. Check for wear

and tear of the sponges. Replace if necessary.

• You can help boost the biological function of your filter

sponge with a bacterial additive, available from your

local stockiest.

A Q U A T E C E Q U I P M E N T . C O M

7/11/17 7:52 am