aquatherm AT1200 Manuale di installazione - Pagina 4

Sfoglia online o scarica il pdf Manuale di installazione per Riscaldatore per piscina aquatherm AT1200. aquatherm AT1200 8. Swimming pool & spa heat pumps
Anche per aquatherm AT1200: Manuale d'uso e manutenzione (6 pagine)

Stampa la pagina

B. HEAT PUMP PLACEMENT & CLEARANCES

WATER IN/OUT PORT INDI-

CATOR LABEL

1. To allow for proper condensation drainage,

use a level slab to elevate the heat pump to

at least the same height as the pool ﬁlter

system slab, or 2 to 3 inches minimum

above grade.

2. Allow the minimum air ﬂow clearances on

top and the sides as shown here. Make sure

the unit can "breathe" well. Do not install

indoors or where the discharge air can ac-

cumulate and be drawn back through the

heater. Make sure the front is accessible

for future service.

3. Keep sprinkler heads at least 6 feet away

from the heat pump. Do not allow the

sprinkler to spray the unit in any way to

prevent damage.

4. If the unit is installed under a roof overhang

or under a roof valley, a gutter or diverter

should be ﬁtted to prevent excessive water

from pouring through the unit.

5. Keep all plants and shrubs trimmed away

from the heater to the minimum clearances

shown here to prevent air coil damage.

6. If the heater is installed above or below

the pool water level by more than 3 feet

you may require an external water ﬂow

switch. See the bottom of page 7 for more

information.

Titanium Instal Manuals.indd 4

FAN DISCHARGE

AIR FLOW OUT

AIR COIL

AIR FLOW IN

ON 3 SIDE

2" THREADED MALE

PIPING CONNECTIONS

Minimum Air Flow

& Access

Clearances

BACK

AIR

COIL

TOP

12"

FRONT

36"

48"

6 FT

-4-

ELECTRICAL CONNECTIONS AND WIRING

5. INTERFACING DIGITAL LOGIC CONTROL MODELS

with Jandy™Aqualink RS & Compool

To interface the "Digital Logic" digital control heat pump models with the Jandy AquaLink RS series

or Compool, run a 2 wire (16 A.W.G. or larger) insulated cable from the device to the heat pump.

Remove the 6 screws from the heaters front service access panel and open. Look for the heaterʼs

solid state circuit board located inside the top portion of the electrical compartment mounted on the

rear wall. Locate, remove and discard the "METAL JUMPER TAB" attached to the bottom terminal

bar and labeled "Jandy/Compool". Then, run a 2 wire cable from the 2 position terminal where the

metal jumper tab was, through the heaterʼs low voltage access port, then to the AquaLink RS or the

Compool control.

NOTE for AquaLink RS and Compool: Turn both heater thermostats all the way up and set the

mode selector switch to pool and do not use the heater controls as the Jandy or Compool now has

thermostatic control over the heater.

for AquaLink

Attach the 2

wire cable to

positions #1

and position

# 2 on the 10

slot, green ter-

minal bar inside

the AquaLink's

power center.

*See the con-

trollers instal-

l a t i o n g u i d e

also.

FOR AQUALINK/COMPOOL

REMOVE METAL JUMPER

GREEN TERMINAL BAR

POSITIONS 1 & 2

JANDY AQUALINK PC BOARD

-13-

for Compool

Attach the 2

JUMPERS

wire cable to

SEE

NOTE #4

the Compool's

power center

board located

on the termi-

nals labeled

"HTR"

*See

the controllers

i n s t a l l a t i o n

guide also.

COM.

2 WIRE CABLE

#14-16 AWG

TERMINAL

"HTR" POSITIONS

COMPOOL

PC BOARD

11/19/04 4:05:50 PM