Arcam DiVA CD62 Manuale - Pagina 6
Sfoglia online o scarica il pdf Manuale per Lettore CD Arcam DiVA CD62. Arcam DiVA CD62 8. Arcam compact disc player handbook cd62
Anche per Arcam DiVA CD62: Manuale di servizio (18 pagine)
Stampa la pagina
Using the CR224 remote control
PROG (Program)
You can program a selection of up to 24 tracks from a disc
to play in any order. Select a track by using the
buttons, then press
PROG
to program the track into memory
('PROGRAM' appears on the display to indicate that you have
started programming a sequence). Repeat these steps to
program the remaining tracks in your selection. Alternatively,
press
PROG
once and enter your track selection using the
The display shows the track numbers programmed, the total
length of the programmed sequence and the number of tracks
programmed (shown by a number below the word 'STEP').
Each time you enter a track the number below 'STEP'
increments by one and fl ashes until you press
If you fail to press
within about fi ve seconds the display
PROG
stops fl ashing and you will have to reselect the track.
Press
to play the program. Press
again to replay the entire
sequence from the start. Press and hold
CLEAR
programmed sequence. Press
PROG
again to exit the program
facility: the display fl ashes 'CONTINUE' and shows '0'.
Skip and Search Track
Skip track backwards and forwards;
Search backwards and forwards (see page 5)
Press
once to display the remaining time of
TIME
the currently playing track. Press again to display the
time remaining on the disc. Press a third time to
turn the text display on.
Press
again and the display reverts to its original
TIME
setting, showing the time elapsed for the current track.
For CDs with text, pressing
once while the disc
TIME
is loaded but not playing displays the artist's name.
Pressing
TIME
a second time displays the total number of
tracks and the total playing time.
Turns the display on or off. Turning the display off generally
produces a slight improvement in sound quality.
Opens and closes the CD tray.
These operate in the same way as the source selector
on the front panel of an Arcam integrated amplifi er.
CD62
6
and
0–9 keypad.
PROG
to confi rm.
to erase the
TIME
DISP (Display)
OPEN
Source selection
0–9 keypad
This allows direct access to individual tracks on the disc.
To select a track, press the corresponding keypad button.
For tracks greater than 9, enter the digits in sequence. For
example, to play track 15, press and hold
1
on the display moves to the left, then press
Playback control
Play, Stop and Pause (see page 5).
REPEAT
To repeat the entire CD or a pre-programmed selection of
tracks press
once: 'REPEAT' lights on the display.
REPEAT
To repeat a particular track, select that track and then press
REPEAT
twice so that 'REPEAT 1' is shown on the display.
you now select a different track, that track is repeated
instead.
To cancel the repeat function press
REPEAT
A–B
This button enables you to repeat any section of music
within a track. Whilst the disc is playing, press the
button at the start of the section you wish to repeat.
'REPEAT' is shown on the display and the letter 'A–' fl ashes.
Press the button a second time when you reach the end
of the section you wish to repeat. The 'A–B' letters stop
fl ashing and remain lit. This section will repeat until you
press
or
or
. The forward search button (
moves forward within the selected loop.
SHUFFLE
Press once to shuffl e play CD tracks (i.e. play them in
a random order). Press again to cancel shuffl e play.
MUTE
Stops sound to the speaker outputs of certain Arcam
amplifi ers.
VOL (Volume) +/–
Adjusts the volume on Arcam remote-controllable amplifi ers.
Note that the volume (+/–) controls and
MUTE
no effect on the audio output level of the CD players.
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control.
Do not place anything in front of the display area on
the CD player (where the IR receiver is located), or the
remote control may not work.
until the number
5
.
If
a third time.
A–B
)
button have