Arcam AVR200 Manuale - Pagina 16

Sfoglia online o scarica il pdf Manuale per Ricevitore Arcam AVR200. Arcam AVR200 19. Surround sound receiver
Anche per Arcam AVR200: Manuale di servizio (15 pagine)

Stampa la pagina
Arcam AVR200 Manuale

Reference

Bi-wiring and bi-amping loudspeakers

Before you start

Bi-wiring your loudspeakers

Bi-wiring improves the sound of your system because it divides
the high and low frequency signal currents into separate
speaker cables. This avoids signal distortions arising from the
high and low frequency currents interacting with one another
within a single cable, as in conventionally wired systems.
You will need:
Speakers – with four input terminals each: these will be marked
HF (High Frequency) and LF (Low Frequency).
Loudspeaker cables – two pairs of cables per loudspeaker
(which may be joined at the amplifi er end if your amplifi er has
only one pair of output terminals per channel). Or, a suitably
terminated cable set (a loom, probably prepared by your dealer
and capable of being used for bi-wiring in one length).
How to bi-wire loudspeakers
AVR200
16
WARNING: Do not make any connections to your
amplifi er while it is switched on or connected to the
mains supply.
Before switching on please check all connections
thoroughly, making sure bare wires or cables are
not touching the amplifi er in the wrong places (which
could cause short circuits) and you have connected
positive (+) to positive and negative (–) to negative.
Always ensure that the volume control on your
amplifi er is set to minimum before starting these
procedures.
1. Remove the terminal links on the rear of your
loudspeakers
WARNING: This step is essential or damage to
your amplifi er may result which is not covered
under warranty.
2. Connect the cables as shown in the diagram below,
ensuring correct polarity at all times.
Arcam AVR200 receiver
R
+
–
+
HF
–
Right
speaker
+
LF
–
Bi-wiring using one set of connections on amplifi er

Bi-amping your system

The performance of your system can be further enhanced over
that achieved with bi-wiring, by extending the principle one stage
further to include separate amplifi cation for the low and high
frequency drive units in each loudspeaker enclosure.
Connect the AVR200 to the high frequency (HF) terminals
and connect your power amplifi er to the low frequency (LF)
terminals.
You will need:
Speakers – with four input terminals each (as with bi-wiring):
these will be marked HF (High Frequency) and LF (Low
Frequency).
Two amplifi ers – one of these would be the AVR200 and the
other an Arcam power amplifi er (e.g. an P75 or P85).
Loudspeaker cables – one pair of cables per loudspeaker or
a suitably terminated cable set (a loom, probably prepared by
your dealer and capable of being used for bi-amping in one
length).
Interconnect cables – one pair of high quality interconnect
cables.
How to set up a bi-amped system
L
+
–
+
HF
–
Left
speaker
+
LF
–
1. Remove the terminal links on the rear of your
loudspeakers.
WARNING: This step is essential or damage to
your amplifi er may result which is not covered
under warranty.
2. Connect the cables as shown in the diagram below,
ensuring correct polarity at all times.
3. Use the interconnect cables to connect the AUDIO PRE-
OUT sockets of the AVR200 to the corresponding PWR
AMP IN sockets of the power amplifi er.
Arcam AVR200 receiver
R
+
–
+
–
HF
Right
speaker
–
LF
+
–
+
–
R
Arcam AP85 power amplifier
Recommended bi-amping confi guration
L
+
–
+
–
HF
Left
speaker
LF
+
–
+
–
L