Axxent MS-200 Manuale operativo - Pagina 4

Sfoglia online o scarica il pdf Manuale operativo per Sistema interfonico Axxent MS-200. Axxent MS-200 4. Intercom systems

Stampa la pagina

Controls on the front side

ON/OFF switch for both rack lights (1). BNC connector as input for rack light

(2). Space for accessories, such as a mobile phone (3),12 V cigarette lighter (4),

SIGNAL light as call indicator (5), CALL button with light (6/7). Below this button

is the ON/OFF switch for the BUZZER tone (6/7), switch for microphone: PTT=

push to talk, OFF and ON (8), VOLUME control for the earphone of the headset (9)

SIDE TONE volume control to set the cueing level of your own microphone (10).

COM CONNECT is a 3 pin XLR male plug for intercom connection. This for example

connect to a beltpack or to another signal light (11) (via a mic cable). HEADSET

connector: 4 pin XLR male (12). RACKLIGHT BNC connector (13). POWER ON/OFF

switch (14). Attention: switch the unit on after you made all the connections

to the intercom components.

Power supply PS-100

Normally beltpacks, loudspeaker stations or signal lights receive their operating

voltage from an intercom main station. These main stations are normally intended

to be rack mounted. During the past few years a trend to the use of digital audio

mixing consoles could be observed, eliminating in many cases the so called „side

racks" since these mixing consoles also have dynamic processors on board.Sound

engineers therefore avoid additional 19" equipment. We have reacted to this trend

and developed an external power supply for small intercom components such as

beltpacks. The voltage supply is delivered by a standard microphone cable. With the

new power supply PS-100 up to 6 beltpacks may be connected.

Controls on the front side

Power switch (1) – Please switch on only after connecting all other compo-

nents. Voltage selector 120/240 V (2). In Europe leave this selector in the 240 V

position otherwise the unit can be dam-

aged. Fuse holder with glass fuses, 5 x 20

mm, 200 mA slow blow (3). Only replace

with fuses of the same current. In case the

fuse blows again sent in the unit must be

return for repair. OVERLOAD LED (4) indi-

cates that possibly too many components have been connected. POWER LED (5).

ProAudio Technik Josef Becker · Zum Wartturm 15 · 63571 Gelnhausen (Germany)

Fon: +49-6051-9140-0 Fax: 9140-59

I N T E R C O M - S Y S T E M

1 2 3

Operation Manual

6/7

9 10

One channel main station MS-100

Most important features of the MS-100: Main station for 19" rack mounting

1 U (44 mm). Like the main station MS-200 it operates as power supply for

up to 14 beltpacks. The model MS-100 oﬀers a 12 V cigarette lighter which

may also serve as power supply for a mobile refrigerator or to charge a cell-

phone. Also two rack light BNC connectors are provided.

Controls on the rear side

Fuse holder (1). Standard glass fuses 5 x 20 mm, 1 A, slow blow, are used. Replace

only with fuse of the same type. In case the fuse blows again the unit has to be

sent in for repair. Voltage connector 120/240 V (2): in Europe this selector must be

in the 240 V position. Switching to a 120 V position may damage the unit (no war-

ranty). Power cord outlet (3), LINE-OUT (4) = 3 pin XLR male connector line level

for recording or as a feed for PA systems. COM CONNECT (5) this 3 pin XLR male

connector is the intercom output for connection of several intercom components

using standard microphone cables.

Controls on the rear side

On the rear side of the power supply PS-100 you will ﬁnd the power cord outlet

and the two XLR intercom connectors (5+6). A total of 6 beltpacks may be

Signal light LP-100

The light dome of the LP-100 is made of white matte

glass and can be noticed even at large distances.

The LP-100 has no controls, solely an intercom

connection in-/ and output. This means that you can

position this signal light in the intercom chain wher-

ever you want and where it is needed. The operation

voltage is carried by the microphone cable.

[email protected] · www.proaudio-technik.de

The case of the power supply is

very rugged and made of steel

with a special coating for years

of ﬂawless operation. Rubber

feet are provided for safe surface

mounting.