Axxess AX-AU12-SWC Manuale di istruzioni per l'installazione - Pagina 6
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Automobile Accessories Axxess AX-AU12-SWC. Axxess AX-AU12-SWC 12. Data interface with swc for audi
Stampa la pagina
CONNECTIONS TO BE MADE
3.5mm jack steering wheel control retention:
• The 3.5mm jack is to be used to retain audio controls on the steering wheel.
For the radios listed below, connect the included female 3.5mm connector with stripped leads, to the
•
male 3.5mm SWC jack from the LD-BX-AU1 or LD-BX-AU2 harness. Any remaining wires tape off and disregard.
•
Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire of
the connector. Then connect the remaining steering wheel control wire, normally Brown/White,
to the Brown wire of the connector .
•
Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire.
•
Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to the
Brown wire.
Note: If your Kenwood radio auto detects as a JVC, manually set the radio type to Kenwood. See
the instructions under changing radio type.
•
XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.
•
Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold separately),
and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.
Note: The radio must be updated to rev. 2.1.4 or higher software.
•
Universal "2 or 3 wire" radio: Connect the steering wheel control wire, referred to as Key-A or
SWC-1, to the Brown wire of the connector. Then connect the remaining steering wheel control wire,
referred to as Key-B or SWC-2, to the Brown/White wire of the connector. If the radio comes with a
third wire for ground, disregard this wire
Note: After the interface has been programmed to the vehicle, refer to the manual provided with
the radio for assigning the SWC buttons. Contact the radio manufacturer for more information.
•
For all other radios: Connect the 3.5mm jack from the LD-BX-AU1 or LD-BX-AU2 harness, into the jack
on the aftermarket radio designated for an external steering wheel control interface. Please refer to
the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.
6
(CONT)
.
INSTALLING THE AX-AU12-SWC
With the key in the off position:
• Connect the 16-pin harness with stripped leads, and either the LD-BX-AU1 or LD-BX-AU2 harness,
into the interface.
• Connect either the LD-BX-AU1 or LD-BX-AU2 harness, to the wiring harness into the vehicle.
Note: If retaining steering wheel controls, ensure the jack/wire is connected before
proceeding onto the next step.
INITIALIZING THE AX-AU12-SWC
• For the steps below, the Red L.E.D. (located inside the interface, next to the potentiometer) can
only be seen while active. The interface does not need to be opened to see the L.E.D.
• Turn the key (or push-to-start button) to the ignition position, the L.E.D. will turn on.
• Within a minute, the L.E.D. will turn off for a couple seconds, then flash slowly (up to (18) times,
indicating which radio is connected to the interface), and then turn off. Pay close attention as
to how many slow flashes there are. This will help in troubleshooting, if need be. Refer to the
L.E.D. feedback section for more information.
• Within a few seconds the L.E.D. will turn on, and the radio will turn off.
• Within a minute the L.E.D. will turn off, and the radio will come back on, indicating the
initialization process is successful.
Note: If the radio does not come back on within a minute, the interface is not communicating to
the vehicle. Turn the key off, check all connections, and then try again. The interface may need to
be reset at this point.
TROUBLESHOOTING
• If the vehicle has engine noise after installing the AX-AU12-SWC, use Axxess part
number AX-AGL610, qty. (2) for Bose, qty. (1) for non-Bose.