Epson AcuLaser C1900 Scheda di configurazione
Sfoglia online o scarica il pdf Scheda di configurazione per Stampante Epson AcuLaser C1900. Epson AcuLaser C1900 2. Epson printer specifications
Anche per Epson AcuLaser C1900: Opuscolo e specifiche (24 pagine)
Stampa la pagina
Setup Sheet
Warnings, Cautions and Notes
w
Warnings
must be followed carefully to avoid bodily injury.
c
Cautions
must be observed to avoid damage to your equipment.
Notes
contain important information and useful tips on the operation of your printer.
4032086-01
XXX
Safety Instructions
Laser Printer Precautions
This printer uses laser technology. Follow the precautions below to ensure safe,
efficient operation.
Be careful not to touch the fuser, which is
marked CAUTION Hot Surface Avoid
Do not insert your hand into the
Contact. If the printer has been in use, the
fuser unit, as it may be very hot.
fuser may be very hot.
Do not attempt to modify or take the
developer cartridge apart. It cannot be
refilled.
Do not touch the toner and avoid all toner
contact with your eyes.
Do not dispose of used developer cartridges,
waste toner collectors, or photoconductor
units in fire, as they can explode and cause
injury. Dispose of them according to local regulations.
Important Safety Instructions
Read all of the following instructions before operating your printer:
The printer weighs about 30kg
(66.1lb). One person should not
attempt to lift or carry the
printer. Two people should
carry it, lifting it by the correct
positions as shown.
Follow all warnings and
instructions marked on the
Left
Right
printer.
Unplug this printer from the wall outlet before cleaning.
Use a well-wrung cloth for cleaning and do not use liquid or aerosol cleaners.
Avoid touching the components inside the printer unless instructed to do so in
this guide.
Never force printer components into place. Although the printer is designed to
be sturdy, rough handling can damage it.
Be sure to keep consumables out of the reach of children.
Do not leave jammed paper inside of the printer. This can cause the printer to
overheat.
Do not use this printer near water.
Do not place the printer on an unstable surface.
Do not put your printer where the cord will be stepped on.
Avoid using outlets that other appliances are plugged into.
Slots and openings in the cabinet and the back or bottom are provided for
ventilation. Do not block or cover them. Do not put the printer on a bed, sofa,
rug, or other similar surface or in a built-in installation unless proper ventilation
is provided.
The interface connector for this printer is Non-LPS (non-limited power source).
Use the type of power source indicated on the label. If you are not sure of the
type of power available, consult your dealer or local power company.
If you are unable to insert the plug into the outlet, contact a qualified electrician.
If you use an extension cord, make sure that the total of the ampere ratings on
the products plugged into the extension cord does not exceed the extension cord
ampere rating.
Never push objects of any kind through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or
electric shock.
Never spill liquid of any kind on the printer.
Except as specifically explained in this guide, do not attempt to service this
product yourself. Opening or removing those covers that are marked
Do Not Remove may expose you to dangerous voltage points or other risks.
Refer all servicing in those compartments to a qualified service representative.
Adjust only those controls that are covered by the operating instructions.
Improper adjustment of other controls may result in damage and may require
repair by a qualified service representative.
Unplug this printer from the wall outlet and refer servicing to a qualified service
representative under the following conditions:
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into it.
C. If it has been exposed to rain or water.
D. If it does not operate normally when the operating instructions are followed.
Adjust only those controls that are covered by the operating instructions
since improper adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore the product
to normal operation.
E. If it has been dropped or the cabinet has been damaged.
F. If it exhibits a distinct change in performance, indicating a need for service.
Finding a Place for the Printer
1
Allow adequate space for easy operation and maintenance.
Dimentions shown in the illustrations above are in millimeters.
Place the printer where you can easily unplug the power cord.
Keep the entire computer and printer system away from potential sources of
interference, such as loudspeakers or the base units of cordless telephones.
c
Caution:
Leave adequate room around the printer to
allow for sufficient ventilation.
Avoid locations that are subject to direct
sunlight, excessive heat, moisture, or dust.
Do not place the printer on a surface that is
smaller than the printer's bottom panel. Doing
so may cause troubles on printing and feeding
due to the internal excessive load of the printer.
Be sure to locate the printer on a flat, wide
surface where the rubber pads can be placed
stably.
Assembling the Printer
2
1. Remove the protective materials.
2. Open the front cover.
3. Remove the protective material.
4. Remove the protective material from
the transfer unit.
5. Install the waste toner collector.
6. Close the front cover.
7. Open the cover on the right.
8. Pull up the green tabs and pull them
down. Remove the protective
materials.
9. Close the cover on the right.
10.Remove the protective materials.
11.Install the MP tray.
Insert straight
into the slots.
Installing the Options
3
Memory Module/ROM Module/Hard Disk Drive
To install the optional 500-Sheet Paper Cassette Unit and Duplex Unit, see the
instructions that come with the packages.
Memory size
32MB, 64MB, 128MB, 256MB or 512MB
®
®
ROM Module
The Adobe
PostScript
3™ Kit ROM module (C12C832531)
Hard Disk Drive
C12C823921
For more detailed descriptions of Memory Module/ROM Module/Hard Disk
Drive, see the online Reference Guide.
w
Warning:
Removing other screws and covers will expose high voltage areas.
Be careful when working inside the printer as some components are sharp and may
cause injury.
c
Caution:
Before you install a Memory Module/ROM Module/Hard Disk Drive, be sure to
discharge any static electricity by touching a grounded piece of metal. Otherwise,
you may damage static-sensitive components.
Make sure that the printer is turned off.
Remove only the five screws attaching the back cover.
1. Turn off the printer.
2. Loosen the five screws and remove the
shield on the back of the printer.
3. When installing the Memory Module/ROM Module/Hard Disk Drive, see the
instructions below.
c
Caution:
Do not force the Memory Module/ROM Module/Hard Disk Drive into the slot.
Be sure to insert the Memory Module/ROM Module/Hard Disk Drive facing
the correct way.
Do not remove any modules from the circuit board. Otherwise, the printer will
not work.
<Memory Module>
RAM slot
<ROM Module>
ROM slot
<Hard Disk Drive>
4. Secure the five screws and close the shield on the back of the printer.
To confirm that the Memory Module/ROM Module/Hard Disk Drive is installed
correctly, print a status sheet.
See "4 Testing and Connecting the Printer".
Interface Cards
Your printer comes with a Type B interface slot. Follow the steps below to install
the optional interface cards.
For more detailed descriptions of interface card, see the online Reference Guide.
w
Warning:
Removing other screws and covers will expose high voltage areas.
Be careful when working inside the printer as some components are sharp and may
cause injury.
c
Caution:
Before you install an interface card, be sure to discharge any static electricity by
touching a grounded piece of metal. Otherwise, you may damage static-sensitive
components.
Make sure that the printer is turned off.
Remove only the two screws attaching the left side cover.