Epson DFX-9000 Manuale d'uso - Pagina 26
Sfoglia online o scarica il pdf Manuale d'uso per Stampante Epson DFX-9000. Epson DFX-9000 28. 9-pin dot matrix printer
Anche per Epson DFX-9000: Manuale d'uso (28 pagine), Specifiche tecniche (2 pagine), Aggiornamento del firmware (1 pagine), Riferimento rapido (12 pagine), Specifiche tecniche (2 pagine), Inizia qui (2 pagine)
Stampa la pagina
http://www.ochimp.com
Safety Instructions
Hot Parts Caution Symbol
This symbol is placed on the print head and other parts to indicate that
K
they may be hot. Never touch those parts just after the printer has been
used. Let them cool for a few minutes before touching them.
Important Safety Instructions
Read all of these safety instructions before using the printer. In addition, follow all
warnings and instructions marked on the printer itself.
❏
Do not place the printer on an unstable surface or near a radiator or heat
source.
❏
Place the printer on a flat surface. It will not operate properly if it is tilted or
placed at an angle.
❏
Do not block or cover the slots and openings in the printer's cabinet, and do
not insert objects through the slots.
❏
Use only the type of power source indicated on the printer's label.
❏
Connect all equipment to properly grounded electrical outlets. Avoid using
outlets on the same circuit as photocopiers or air control systems that regularly
switch on and off.
❏
Do not use a damaged or frayed power cord.
❏
If you use an extension cord with the printer, make sure the total ampere rating
of all devices plugged into the extension cord does not exceed the cord's ampere
rating. Also, make sure the total ampere of all devices plugged into the electrical
outlet does not exceed the electrical outlet's ampere rating.
❏
Unplug the printer before cleaning it, and clean it with a damp cloth only.
❏
Do not spill liquid onto the printer.
❏
Except as specifically explained in the user documentation, do not attempt to
service the printer yourself.
❏
Never replace the print head yourself; you may damage the printer. Also, other
parts of the printer must be checked when the print head is replaced.
❏
You need to move the print head by hand to replace the ribbon cartridge. If
you have just used the printer, the print head may be hot; let it cool for a few
minutes before touching it.
❏
Adjust only those controls that are covered by the operating instructions.
26 Safety Instructions
http://www.ochimp.com
For More Info
Click Here ===>
❏
Unplug the printer and refer servicing to qualified service personnel under
the following conditions: if the power cord or plug is damaged, if liquid has
entered the printer, if the printer has been dropped or damaged, if it does not
operate normally or exhibits a distinct change in performance.
FCC Compliance Statement for United States Users
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio or television reception. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause interference to radio and television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
❏
Reorient or relocate the receiving antenna.
❏
Increase the separation between the equipment and receiver.
❏
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
❏
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will
invalidate the FCC Certification of this device and may cause interference levels
which exceed the limits established by the FCC for this equipment. It is the
responsibility of the user to obtain and use a shielded equipment interface cable with
this device. If this equipment has more than one interface connector, do not leave
cables connected to unused interfaces.
Changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate the equipment.
For Canadian users
This Class B digital apparatus meets all requirements of the Canadian Interface
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matériel brouileur du Canada.