Cisco 2960-24LT-L - Catalyst Switch Scheda tecnica - Pagina 16
Sfoglia online o scarica il pdf Scheda tecnica per Interruttore Cisco 2960-24LT-L - Catalyst Switch. Cisco 2960-24LT-L - Catalyst Switch 28. Switching portfolio
Anche per Cisco 2960-24LT-L - Catalyst Switch: Scheda tecnica (11 pagine), Scheda tecnica (21 pagine), Opuscolo e specifiche (10 pagine), Descrizione (1 pagine)
Table 6.
Connectors and LED Indicators
Cisco Catalyst 2960-S with SFP+ based ports:
● 10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 unshielded twisted-pair (UTP) cabling
● 100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling
● 1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-T SFP-based ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-SX, -LX/LH, -ZX, -BX, -T,* -FX,* and coarse wavelength-division multiplexing (CWDM) SFP-based ports: LC fiber connectors
(single/multimode fiber)
● 10GBASE-LR, SR, LRM, CX1 SFP+ based ports
* The Cisco Catalyst 2960-S with SFP+ does not support the GLC-FE-100BX, GLC-FE-100FX, GLC-T, or GLC-FE-100LX.
Cisco Catalyst 2960-S and 2960 with SFP-based ports:
● 10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 UTP cabling
● 100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling
● 1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-T SFP-based ports**: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-SX -LX/LH, -ZX, -BX, -T,* -FX,* and CWDM SFP-based ports: LC fiber connectors (single/multimode fiber)
● 100BASE-LX, -BX, -FX SFP-based ports: LC fiber connectors (single/multimode fiber)
* GLC-T and GLC-GE-100FX are not supported on the Cisco Catalyst 2960-8TC-S, 2960-8TC-L, or 2960G-8TC-L switches.
** 1000BASE-T not supported on Cisco Catalyst 2960-S switches.
Cisco Catalyst 2960-S FlexStack stacking cables:
CAB-STK-E-0.5M
CAB-STK-E-1M
CAB-STK-E-3M
Cisco Catalyst 2960-S console cables:
CAB-CONSOLE-RJ45
CAB-CONSOLE-USB
● Customers can provide power to a switch by using the internal power supply. The connector is located at the back of the switch. These switches do
not have a redundant-power-supply port.
● The internal power supply is an auto-ranging unit
● The internal power supply supports input voltages between 100 and 240 VAC
● Use the supplied AC power cord to connect the AC power connector to an AC power outlet.
● Cisco RPS connector:
The Cisco RPS connector offers connection for an optional Cisco RPS 2300 that uses AC input and supplies DC output to the switch.
The connector offers a 2300W redundant power system that supports up to 6 external network devices and provides power to 2 failed devices at a
time.
The connector automatically senses when the internal power supply of a connected device fails and provides power to the failed device, preventing
loss of network traffic.
Only the Cisco RPS 2300 (model PWR-RPS2300) should be attached to the redundant-power-system receptacle.
Note: The Cisco Catalyst 2960-8TC-L and 2960G-8TC-L do not have RPS ports.
● Per-port status: Link integrity, disabled, activity, speed, and full duplex
● System status: System, RPS, link status, link duplex, PoE, and link speed
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Connectors, LED Indicators, and Dimensions
FlexStack stacking cable with a 0.5 m length
FlexStack stacking cable with a 1.0 m length
FlexStack stacking cable with a 3.0 m length
Console cable 6 ft with RJ-45
Console cable 6 ft with USB Type A and mini-B connectors
Data Sheet
Page 16 of 28