Sharp Carousel R-90GC Manuale operativo - Pagina 6

Sfoglia online o scarica il pdf Manuale operativo per Forno a microonde Sharp Carousel R-90GC. Sharp Carousel R-90GC 36. High speed oven
Anche per Sharp Carousel R-90GC: Opuscolo e specifiche (8 pagine), Opuscolo e specifiche (5 pagine), Manuale operativo (36 pagine), Manuale operativo (32 pagine)

Stampa la pagina

R-90GC(S) O/M

INSTALLATION INSTRUCTIONS

1. Remove all packing materials from the oven cavity, (do not remove the waveguide cover), and the feature

sticker from the outside of the door, if there is one. Check the unit for any damage, such as a misaligned

door, damaged door seals around the door or dents inside the oven cavity or on the door. If there is any

damage, please do not operate the oven until it has been checked by a SERVICE CENTRE APPROVED

BY SHARP and repaired, if necessary.

2. Accessories provided

Turntable

Turntable support

Low rack

3. Since the door may become hot during cooking, you should place or mount the oven so that the bottom of

the oven is 80 cm or more above the floor. You should also keep children away from the door to prevent

them burning themselves.

4. Place the turntable support to the turntable motor shaft on the floor of the oven cavity. And place the

turntable on the turntable support. Make sure the turntable and turntable support are centrally located and

locked together. NEVER operate the oven without the turntable support and turntable.

5. The oven should not be installed in any area where excessive heat and steam are generated, for example,

next to a conventional oven unit.

The oven should be installed so as not to block ventillation openings.

Allow at least 40 cm on the top, 5 cm on the both sides and at the rear of the oven for free air space.

This oven shall not be installed below bench height.

6. Building the oven into the wall. A Sharp built-in kit model number EBR-90GKST is available which enables

the microwave oven to be integrated within a kitchen, the kit is available from your retailer. This built-in kit

has been tested according to Australian Standards. Sharp does not recommend the use of any other built-

in kit.If the oven is to be positioned near a conventional oven, ensure that adequate space is allowed, and

a suitable heat shield is incorporated between the two to prevent damage to the oven and the built-in kit

caused by heat.

7. Neither the manufacturer nor the distributors can accept any liability for damage to the machine or personal

injury for failure to observe the correct electrical connecting procedure.

The A.C. voltage must be single phase 230-240V, 50Hz.

8. This appliance must be earthed.

9. Operate the oven from a general purpose domestic outlet. If a generator is used, do not operate the oven

with non-sinusoidal outputs.

10. Before using the oven for the first time, it is recommended to do the Refresh Cycle. Refer to page 19.

OVEN DIAGRAM

1. Door open handle

2. Oven lamp

3. Door hinges

4. Door safety latches

5. See through door

6. Door seals and sealing

surfaces

7. Turntable motor shaft

8. Waveguide cover

9. Control panel

Warning:

The accessories will become very hot when in use. Use thick oven gloves when inserting/removing the food or

turntable from the oven to PREVENT BURNS.

R-90GC(S) O/M,01-14

4) High rack

5) Splash guard

6) Operation manual

10. Digital readout

11. Oven cavity

12. Ventilation openings

13. Power supply cord

14. Outer cabinet

15. Ventilation cover

(Do not remove)

16. Turntable

17. Turntable support

18. Low rack

19. High rack

7) Cookbook

8) Touch guide

20. Splash guard

21. Rating label

Accessories

The racks and splash guard are used for

cooking in Convection, Dual or Grill mode.

03.7.11, 2:13 PM