DIGITAL DELAY Mega 400 Manuale di istruzioni - Pagina 8

Sfoglia online o scarica il pdf Manuale di istruzioni per Automobile Accessories DIGITAL DELAY Mega 400. DIGITAL DELAY Mega 400 14.

To enter a new Programmable Throttle Stop Override amount, repeatedly press the D key until the letters A and B are

shown next to the S.L.E. and the P.T.S.O. (D3). The Programmable Throttle Stop Override information is shown to the right

of the letter B. If the P.T.S.O. is turned off, two dashes and the word "OFF" will be to the right of the letter B. If a number is

displayed the P.T.S.O. is turned on and the number shown is the current P.T.S.O. time. To change the amount of time press

the B key, the four digits to the right of the letter B will go blank and the word "OFF" will be shown just below and to the left

of where the digits had been. At this point if no numbers are entered the P.T.S.O. will be turned off. If any number greater

than zero is entered the P.T.S.O. will automatically be turned on. Enter the new P.T.S.O. amount using the numerical keys,

leading zeros do not have to be entered. Any number from 00.01 to 99.99 seconds can be used.

To set the Throttle Modes or Throttle Range, repeatedly press the D key until the letters A and B are shown next to

Throttle 1 and Throttle 2 (D4). The Throttle 1 mode and Range are shown to the right of the letter A and Throttle 2 mode and

Range are shown to the right of the letter B. To the right of the letter A either "lo" or "Hi" will be shown, this is the Throttle

Range and only affects the first and second stages. The first and second stage times can be set to any number from 0.000 to

9.999 seconds when in "lo" Range and from 00.00 to 99.99 seconds when in "Hi" Range. Above the Throttle Range setting

the words "off on off on" or "on off on off" this is the Throttle Mode. To change either Throttle 1 Range or Mode repeatedly

press the A key until the desired Range and Mode combination is shown on the display. Throttle 2 works in much the same

way as Throttle 1 does except for two differences. First the S.F.O. Mode must be set to a "2" or Throttle 2 is turned off.

Second is the Throttle Mode indicators are below the Range settings and only "on off" or "off on" will be shown. It must just

be understood that the Throttle Mode would simply repeat for stages 3 and 4.

If the S.F.O. mode is set to any number other than a "1" or a "2", two dashes will be shown along with the word

"OFF" below the dashes indicating Throttle 2 is off.

To set a new stage time, repeatedly press the E key until Throttle 1 is shown on the display and the letters A and B are

shown next to Stage 1 and Stage 2 (E1). To change stages 3 or 4 press the E key again so the letters A and B are shown next

to Stage 3 and Stage 4 (E2). The stage times can be changed by following the same procedure for entering a new number as

instructed in Setting New Dial-In Times. Entering all zeros into any stage turns that stage off.

To set a new stage time for Throttle 2 the S.F.O. Mode must first be set to a 2. Then repeatedly press the E key until

Throttle 2 is shown on the display and the letters A and B are shown next to Stage 1 and Stage 2 (E3). To change stages 3 or 4

press the E key again so the letters A and B are shown next to Stage 3 and Stage 4 (E4). The stage times can be changed by

following the same procedure for entering a new number as instructed in Setting New Dial-In Times. Entering all zeros into

any stage turns that stage off.

If the S.F.O. mode is set to any other mode other than 2 the access to Throttle 2 stage times will be denied.

Setting the Programmable

Throttle Stop Override (P.T.S.O.)

Setting Throttle

Modes and Throttle Ranges