Digital Lumens BBD43 Manuale di istruzioni per l'installazione - Pagina 5

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Camera Accessories Digital Lumens BBD43. Digital Lumens BBD43 6.

Stampa la pagina

BBD43 (UL)

GETTING STARTED

Helpful Hints

—

BBD43 (battery backup) provides a temporary power

source to DLE luminaires in the event that facility power is

lost or disconnected. One BBD43 unit will provide power to

a single light bar (see Note below) on a DLE luminaire for

90-180 minutes.

If you are installing BBD43 on a DLE-Uplight luminaire,

verify that the emergency light bar is oriented downward

(facing the floor) to ensure sufficient lighting in an

emergency situation. Refer to Identifying Emergency

Light Bar & BBD43 Placement to identify the emergency

light bar location, and the correct placement of the BBD43

unit, for each of the DLE luminaires.

Refer to Understanding DLE Luminaire Wiring

Configurations to identify slight variations within the

wiring compartments on each of the DLE luminaires.

Refer to Identifying Emergency Light Bar &

Note:

BBD43 Placement to identify the emergency light bar

location for each of the DLE luminaires. Note that the

DLE-48 luminaire requires two (2x) BBD43 units, one

installed on each end.

Identifying Emergency Light Bar

BBD43

Placement

Observe the location of the designated emergency light bar,

and the correct placement of the BBD43 unit(s), on each DLE

luminaire. If installing BBD43 on an uplight luminaire, ensure

the emergency lightbar is oriented downward (facing the

floor) to ensure sufficient lighting in case of an emergency

(Illustration 1).

Understanding DLE Luminaire

Wiring Configurations

Before you begin, observe the slight variations in the wiring

configurations among the DLE luminaires (Illustration 2).

Illustrations and wiring configurations in these

Note:

instructions reflect the DLE-24 luminaire

Prepare Luminaire and

Carefully, use a flat-head screwdriver to pry off the wiring

compartment cover on the DLE luminaire (Illustration 3).

Use a #2 Phillips

screwdriver to remove the bottom

faceplate screw. The screw is no longer needed

(Illustration 4).

Remove the BBD43 unit and accessories from the

packaging.

Note:

You must disconnect power to the luminaire before

installing a BBD43 unit. Failure to disconnect power will

result in hardware failure.

BBD43 Installation Instructions

BBD43

Hardware

INSTALLATION INSTRUCTIONS

Make Electrical Connections

Default wiring configurations enable facility power and data to

connect directly to the luminaire (see below). In this step, you

will extend these connections to include the BBD43 unit within

the circuit (Illustration 5). By default, the BBD43 unit ships

with the external power, data, and internal power (not shown)

cables disconnected.

Unplug the power connector (red/black or orange/gray)

from the DLE luminaire, and plug it into the two-position

header on the BBD43, as shown (Illustration 6).

Locate the power connection (red/black) coming from

the BBD43, and plug it into the two-position header on

the luminaire, replacing the connector you just removed

(Illustration 7).

Locate the data connector coming from the BBD43,

and plug it into the five-position header on the luminaire

(Illustration 8).

Refer to Understanding DLE Luminaire Wiring

Note:

Configurations for information on luminaire-specific

configurations.

Mount and Secure

BBD43

Secure the top retention hooks (2x) to the luminaire

faceplate, as shown (Illustration 9).

Rotate BBD43 to cover and align both open wiring

compartments. Ensure all wires are tucked safely into the

luminaire wiring compartment (Illustration 10).

Secure the bottom retention hook on the BBD43

unit to the bottom edge of the luminaire faceplate

(Illustration 11).

Use the screw (provided with BBD43) to secure the unit to

the luminaire.

BBD43 is built with three retention hooks (2x on top

Note:

of the unit housing, and one on the bottom) to secure the

hardware to the luminaire.

Connect Internal Power On

On the BBD43 unit, remove the access cover

(Illustration 12).

Connect the two-position battery connector within the

compartment (Illustration 13).

Replace the access cover.

To ensure maximum performance, BBD43 ships with

Note:

the battery disconnected. You must make this connection

before completing hardware installation.

to Luminaire

BBD43

Unit