Ricoh AP600N Manuale di installazione rapida - Pagina 2
Sfoglia online o scarica il pdf Manuale di installazione rapida per Accessori per stampanti Ricoh AP600N. Ricoh AP600N 2. Sap printing
Anche per Ricoh AP600N: Manuale di installazione (1 pagine), Manuale (12 pagine)
Stampa la pagina
CONNECTING THE POWER
Note
❒ When loading paper other than A4 L (long-edge
CORD
feed) or 8
1
/
" x 11" L (long-edge feed), adjust the
2
paper size dial to match the size and feed direction
of the paper in the paper tray.
Caution
• When you pull the plug out of the socket, grip
the plug to avoid damaging the cord and caus-
ing a fire or an electric shock.
• It is dangerous to handle the plug with wet
hands. An electric shock might occur.
Check that the power switch is turned off.
ZKGH200E
❒ When you load paper lager than A4 K (short-edge
feed) or 8
1
/
" x 11" K (short-edge feed), you should
2
extend the tray. For more information, see "Paper
and Other Media Supported by this Printer" in
the Printer Reference provided as a PDF file on the
CD-ROM labeled "Operating Instructions".
Carefully slide the paper tray into the printer
until it stops.
Securely insert the power cord plug into the wall
socket.
SELECTING THE PANEL
ZKGH190E
DISPLAY LANGUAGE
Important
Select a language following the procedures
❒ Confirm that the setting of the paper size dial
described.
matches the size and feed direction of the paper
The message for the selected language will
in the tray. Otherwise, the printer might be
damaged or a printing problem might occur.
appear on the panel display.
❒ Do not slide the paper tray in and out with force.
If you do, the front and side paper guides will
Note
move out of the place.
❒ The default setting is English.
❒ If you want to use the English panel display, the
following procedures are unnecessary.
Check that the power switch is turned on.
Press the {Menu} key.
On Line
Job Reset
Form Feed
Power
"Menu" appears on the panel display.
Press the {L} or {M} key until the following
message appears on the panel display.
Menu:
Language
Press the {Enter
} key.
Press the {L} or {M} key until the language
you want to select appears on the panel display.
Press the {Enter
} key.
Press the {On Line} key.
The settings are applied and the ready message appears on the panel
display.
ZKGH205E
PRINTING A CONFIGURATION
PAGE
You can check if the printer works properly by
printing a configuration page.
However, you cannot check the connection
between the printer and the computer by printing
the configuration page.
Check that the power switch is turned on.
Press the {Menu} key.
"Menu" appears on the panel display.
Press the {L} or {M} key until the following
message appears on the panel display.
Menu:
List/Test Print
Press the {Enter
} key.
The following message appears on the panel display.
List/Test Print:
Config.P/Er.Log
Menu
Press the {L} or {M} key until the following
message appears on the panel display.
Escape
List/Test Print:
Config. Page
Enter
Press the {Enter
} key.
Error
Data In
The test printing will start.
ZKGS020N
Important
❒ If you cannot complete the test printing correctly,
check if an error message appears on the panel
display. For more information about error
messages, see "Troubleshooting" in the Printer
Reference provided as a PDF file on the CD-ROM
labeled "Operating Instructions".
CONNECTING THE PRINTER TO A COMPUTER
❖ Network connection
❖ Parallel connection
Turn off the power switch.
Important
❒ The parallel interface cable is not provided with
the printer. Make sure that the interface cable
you use is appropriate for your computer.
Loop the network interface cable and attach
❒ The printer's parallel connection is a standard
the ferrite core.
bi-directional interface. It requires a standard
36-pin parallel cable compliant with IEEE 1284
Note
and an available parallel port on your computer.
❒ The network interface cable loop should be about
❒ To avoid electrical interference, use a shielded
15 cm(6")(
) from the end of the cable (on the
cable.
end closet to the printer). The ferrite core at the
end of the cable should be a ring type ferrite core.
Note
❒ Do not use a parallel cable more than 2.5 meters
(8.2 feet) long.
Turn off the power switch.
ZKGP321E
Turn the computer off.
Attach the network interface cable to the
jack on the board.
Attach the interface cable to the interface con-
nector of the printer. Secure the cable with the
metal fittings as shown in the illustration.
ZKGT290E
Connect the other end of the network interface
cable to the network.
Turn on the power switch.
Check the LEDs on the ethernet port.
Attach the other end of the interface cable to
the interface connector of the computer. Se-
cure the cable.
Important
❒ Rating voltage of the parallel interface connector
1
for the computer ; Max. DC5V.
2
ZKGH260E
1 is lit when the printer is securely connected to the network.
2 is lit when 100BASE-TX is in use and not lit when 10BASE-T is in
use.
❖ USB connection
Important
❒ The USB interface cable is not provided with the
printer. Make sure that the USB interface cable
you use is appropriate for your computer.
Attach the USB interface cable to the USB in-
terface connector of the printer. Secure the
cable.
ZKGT300E
Attach the other end of the interface cable to
the USB interface connector of the computer
or the USB Hub. Secure the cable.
Note
❒ USB connection is possible with Windows 98 SE/
Me, Windows 2000/XP/Server 2003, Mac OS 9.x
and Mac OS X.
❒ When using Windows 98 SE/Me, install the "USB
Printing Support" software. The support speed
with Windows 98 SE/Me is equivalent to USB 1.1.
❒ USB connection with Macintosh is only possible
via the standard USB port on the printer body.
The support speed with Macintosh is equivalent
to USB 1.1.
ZKGX115E
SETTING UP FOR PRINTING
Printing requires installation of a printer driver
for the operating system.
Reference
❒ See "Printer Drivers for This Printer" in the
Setup Guide.
❒ If you want to install options, see "Installing
Options" in the Setup Guide.
Copyright © 2003 G091-8627
Printed in China
EN USA