Ace X Manuale operativo - Pagina 3

Sfoglia online o scarica il pdf Manuale operativo per Apparecchiature di prova Ace X. Ace X 7.

Stampa la pagina

Preparation for the test:

1. Open the battery compartment cover at the back of

the device: First push the cover up and then sideways.

Then you have to remove the small paper inside the

battery compartment which prevents the battery

discharge. If you exchange old batteries against new

ones please mind the battery polarity (+/- pole).

2. For the active mode operation put a mouthpiece on

the mouthpiece connection, which is on top of the

device. Make sure it is attached properly. Use a differ-

ent mouthpiece for each test person. Avoid blowing

cigarette smoke into the tester! The passive mode is

described in chapter "Conducting the measurement".

ACE INSTRUMENTS RECOMMENDS:

ALWAYS USE A NEW MOUTHPIECE FOR EACH PER-

SON AND TEST THAT IS CONDUCTED. ACE INSTRU-

MENTS ASSUMES NO LIABILITY FOR ANY DAMAGES

WHICH ARISE WHEN SEVERAL PEOPLE USE THE

SAME MOUTHPIECE FOR MULTIPLE TESTS.

ONLY USE THE PROVIDED SINGLE PACKED AND

HYGIENIC MOUTHPIECES – MORE ARE AVAILABLE

AT WWW.ACE-INSTRUMENTS.NET. DURING EACH

TEST THE BREATHALYZER´S INTERNAL AND EXTER-

NAL PARTS COME INTO CONTACT WITH HUMAN

SECRETION (SALIVA, BLOOD, SWEAT, ETC.)!

USE SAFTEY GLOVES WHEN PULLING OUT A

MOUTHPIECE USED BY ANOTHER PERSON!

YOU CAN BUY APPROPRIATE GLOVES E.G. AT

ACE TECHNIK (WWW.ACE-TECHNIK.DE).

Conducting the measurement:

1. Press the power button to turn on the device

(the device beeps once).

2. The device warms up until you can see "0" on the

display (additionally the device beeps twice).

3.a) Active mode: As soon as you can see "0" on the

display blow through the mouthpiece into the

unit for 4 seconds (you can hear a beep tone

during the test) until the sound (a "tic-tac" tone)

concludes.

3.b) Passive mode: For this mode you don't need a

mouthpiece. As soon as you can see "0" on the

display, hold the mouthpiece connection on top

of the device in front of your mouth and press the

power button while you exhale. You see 4 times a

"0" blinking on the display and then the result: If

you see "P" (= Pass) then the test result is below

0.02% BAC and if you see "F" (= Fail) then the test

result is higher than 0.02% BAC. For DUI the legal

limit in the USA is 0.08% BAC (status: Oct 2016).

If you press the power button constantly for 2 seconds, you can

see the letter "C" and "A" - each followed by a number. Please

read the display indications for the explanation of the meaning!

IMPORTANT NOTICE: WHEN YOU HAVE EATEN,

DRUNKEN ALCOHOL OR SMOKED A CIGARETTE,

WAIT AT LEAST 15 MINUTES BEFORE STARTING THE

MEASUREMENT. ANY TEST CONDUCTED PRIOR TO

THE EXPIRATION OF THE RECOMMENDED WAITING

PERIOD WILL RESULT IN INACCURATE RESULTS.

IF THE TEST RESULT IS BELOW 0.005 % BAC THEN

THE DEVICE SHOWS 0.000% BAC ON THE DISPLAY.

THIS HAPPENS BECAUSE AT A LOW RANGE OF

ALCOHOL CONCENTRATION IT IS POSSIBLE TO

MEASURE OTHER MATERIALS IN YOUR MOUTH.

Only the usage of original ACE mouthpieces ...

Guarantees test result accuracy

Guarantees 100 % hygenity

Guarantees full warranty of this device

ACE INSTRUMENTS ADVISES:

EVEN IF YOU GET A RESULT MEANING „SAFE RANGE",

YOU SHOULD NEVER DRIVE AFTER CONSUMING

ALCOHOL OR DO ANY OTHER ACTIVITIES THAT ARE

SEVERELY IMPAIRED BY ALCOHOL CONSUMPTION

AND MIGHT ENDANGER YOUR HEALTH AND SAFETY

OR THE HEALTH AND SAFETY OF OTHERS.