Ace SDH38-500EU Manuale di istruzioni per il funzionamento e il montaggio - Pagina 3

Sfoglia online o scarica il pdf Manuale di istruzioni per il funzionamento e il montaggio per Apparecchiature industriali Ace SDH38-500EU. Ace SDH38-500EU 6. Safety shock absorbers

Stampa la pagina
Safety Shock Absorbers SDH38 (high rack damper, optimised characteristic)
3
Mounting instructions and mounting accessories
Installation instructions
Before installation and use check whether the identification num-
ber on the damper or on the packaging matches the respective
designation on the delivery note.
Operating temperature range: -20 °C to +60 °C
Mounting: As required but always in such a way that the entire
damper stroke is used. The dampers must always be mounted
in such a way that the forces are introduced centrally over the
piston rod in the damper. The maximum side load angle must
not be exceeded. Safety dampers must not be exchanged from
one installation site to another if the conformity of the throttle
characteristic curve is not ensured.
WARNING
Take particular care that the customer-specific
identification number at the end of the damper designation
matches the number on the delivery note. The field data
to be read from the type plate, such as moving mass and
maximum impact velocity, must be compared with the
technical design. This ensures that the damper is the right
size for its use. Otherwise you risk damaging the shock
absorbers and/or machine by overstressing materials.
The gas accumulators of the SDH38 to SDH63 safety shock
absorbers are filled with nitrogen ex works. The respective
filling pressure (5 bar) can be found on the damper
label. The dampers may only be operated with this filling
pressure. A reduced filling pressure can lead to serious
malfunctions.
During installation of the dampers, moving masses can
lead to injuries due to inadvertent starting. Secure moving
masses against inadvertent moving.
The dampers may be unsuitable for use and have an
insufficient damping effect. Check the specific suitability
of the dampers before installation.
If operated outside of the operating temperature range,
the damper can lose its function. Operating temperature
range must be maintained. Do not paint dampers due to
heat emission.
Fluids, gases and dirt particles in the surrounding area can
attack or destroy the seal system of the damper and cause
it to fail. Protect or encapsulate piston rod and seal system
from external materials in the surrounding area.
Damage to the piston rod surface can destroy the seal
system. Do not grease, oil piston rod etc. and protect
against dirt particles.
The piston rod can be torn from the damper. Do not load
the piston rod with tensile stress.
Damper can tear off upon impact. Always lay out the
connection structure in such a way that the maximum
occurring forces can be absorbed with sufficient safety.
Safety shock absorber check after a damper impact.
Check that the piston rod returns to the initial position,
the damper is not leaking and the mounting elements are
properly secured.
21_22_0019 Issue 05.2022
Stand 03.2021
Emergency stop application: After an emergency stop, check
that the piston rod returns to the initial position, the damper is not
leaking and the mounting elements are properly secured. Make
sure that no damage has occurred to the piston rod, the body, or
the mounting hardware.
Regular start-up: Safety shock absorbers can be regularly
started up with 100 % stroke utilisation with a creep speed of 1/10
of the max. impact velocity.
Checking: A regular check should take place at an interval of no
more than three months.
Commissioning
First impacts on the shock absorber should only be tried after
correctly mounting and with reduced impact velocity and – if
possible – with reduced load. Differences between calculated and
actual operating data can then be detected early on, and damage
to the system can be avoided. If the safety dampers were selected
on calculated data that does not correspond to the maximum
possible loading (i.e. selection based on drive power being
switched off or at reduced impact velocity) then these restricted
impact conditions must not be exceeded during initial testing
or subsequent use of the system. Otherwise you risk damaging
the shock absorbers and/or machine by overstressing materials.
After the initial trial, check that the piston rod fully extends again
and that there are no signs of oil leakage. Also check that the
mounting hardware is still securely tightened. Make sure that no
damage has occurred to the piston rod, the body, or the mounting
hardware.
Performance data and dimensions
Energy capacity
1
TYPES
Nm/cycle
SDH38-50EU
SDH38-100EU
SDH38-150EU
SDH38-200EU
SDH38-250EU
SDH38-300EU
SDH38-350EU
SDH38-400EU
SDH38-500EU
SDH38-600EU
SDH38-700EU
SDH38-800EU
The values apply to mounting style Front Flange and Foot Mounting. For mounting style Rear Flange, please consult ACE.
1
In case of an existing side load angle, please consult ACE.
SDH38-F Front Flange
18
115
Ø
Ø
120
B
160
A max
SDH38-S Foot Mount
18
30
115
Ø
Ø
61
60
36
160
D ± 1
190
Mounting accessories
If using accessory parts and mounting elements, note the respec-
tive separate mounting instructions for accessories.
Reacting force
Return Force min.
Return Force max.
1
N
N
N
3,600
80,000
600
700
7,300
80,000
600
700
10,900
80,000
600
700
14,500
80,000
600
700
18,200
80,000
600
700
21,800
80,000
600
700
25,500
80,000
600
700
29,100
80,000
600
700
36,400
80,000
600
700
43,600
80,000
600
700
50,900
80,000
600
700
58,200
80,000
600
700
ACE Stoßdämpfer GmbH · Postfach 1510 · D-40740 Langenfeld · T +49 (0)2173 - 9226-10 (Technik -20) · F +49 (0)2173 - 9226-19 · [email protected] · www.ace-ace.com
SDH38-R Rear Flange
20
36
55
18
20
Ø
Ø
Ø
15
120
Stroke
160
30
36
55
Ø
Ø
15
Stroke
E max
A max
Packaging disposal
Please dispose of the transportation packaging in an environ-
mentally-friendly manner. Recycling packaging materials saves
raw materials and reduces waste. The packaging materials do not
contain any prohibited materials.
Stroke
A max.
B
D
E max.
mm
mm
mm
mm
mm
50
270
204
165
84
100
370
254
215
134
150
470
304
265
184
200
585
369
330
234
250
685
419
380
284
300
800
484
445
334
350
900
534
495
384
400
1,015
599
560
434
500
1,230
714
675
534
600
1,445
829
790
634
700
1,660
944
905
734
800
1,875
1,059
1,020
834
ACE Stoßdämpfer GmbH · www.ace-ace.com
115
36
55
Ø
Ø
Ø
15
B
Stroke
A max
Mounting type
F and R
S
Weight
Weight
kg
kg
14.0
13.7
15.5
15.7
17.0
17.2
20.0
19.7
22.0
21.7
24.0
23.7
26.0
25.7
28.0
28.2
32.0
32.2
36.0
36.2
40.0
40.2
44.0
44.2