Cisco Codec C Series Manuale introduttivo - Pagina 19
Sfoglia online o scarica il pdf Manuale introduttivo per Sistema di conferenze Cisco Codec C Series. Cisco Codec C Series 41. Telepresence conference system
Anche per Cisco Codec C Series: Manuale d'uso (44 pagine), Manuale introduttivo (35 pagine), Manuale introduttivo (32 pagine), Manuale introduttivo (42 pagine), Manuale introduttivo (46 pagine)
Stampa la pagina
Cisco TelePresence Video Systems
Contents
Configuring IP
(When not set by a provisioning system)
Your video conference system supports IP version 4 (IPv4),
IP version 6 (IPv6) and Dual, which is the default setting. In all
three cases, the IP parameters can be assigned automatically
by the network, or you can set everything manually. When set
to Dual, the network interface can operate on both IP versions,
and have both an IPv4 and an IPv6 address.
If you wish to set the parameters manually, contact your network
administrator to obtain the required parameters.
If you choose to set the IP settings manually while using the
Dual mode, you have to set both the IPv4 and the IPv6 settings.
Start from point 2 in the instructions.
If an IP address is already assigned to your system, you find
the current IPv4 and/or IPv6 address on the System Information
page: Go to
Home > Settings > System
The IPv4 Address and/or IPv6 Address of the system is shown
in the
Network
section on the System Information page.
Press
Exit
(the right most function key) to exit.
NOTE:
You must restart the system after changing the IP stack
settings for the changes to take effect.
Always save the new value when you change a setting
• Drop down list selection: Navigate to the correct value
and press the
OK
( ) key to save, or press the left arrow
key
to leave without saving.
• Text entry in an input field: Enter the text, navigate to
Ok/Save
to save the change, or navigate to
to leave without saving; then press the
confirm.
Back to task overview
D14639.12 Video Systems Getting Started Guide TC7.0, DECEMBER 2013.
Introduction
User interfaces
To set or change the IPv4 settings
1.
Select IP version
Go to
Home > Settings > Administrator settings > Advanced
configuration > Network
2.
Select automatic or manual IP assignment
Go to
IPv4 >
automatic IP assignment; select Static, if you want to set
the IP address manually.
a. If you selected DHCP, the IP configuration is complete.
b. If you selected Static, enter the Address,
and Gateway. Go to the
enter the DNS server address in the
input field.
information.
Press
Home
3.
* IP assignment:
DHCPv6: All IPv6 addresses, including options like the DNS and NTP
Cancel
server addresses, are obtained automatically from a DHCPv6 server.
OK
( ) key to
Autoconf: The system and gateway IP addresses will be assigned
automatically. The options, e.g. NTP and DNS server addresses, must be
set/assigned according to the DHCP Options setting. **
Static: The system and gateway IP addresses must be configured
manually. The options, e.g. NTP and DNS server addresses, must be set/
assigned according to the DHCP Options setting. **
Confirguration
Configuration
1. Go to
IPStack
and select IPv4.
Assignment. Select DHCP, if you want
Subnet
Mask,
Network 1 > DNS
section and
Server 1 Address
(
) to return to the home menu.
19
Getting Started Guide
Appendices
To set or change the IPv6 settings
1.
Select IP version
Go to
Home > Settings > Administrator settings > Advanced
configuration > Network
1. Go to
IPStack
2.
Select automatic or manual IP assignment
Go to
IPv6 >
Assignment. Select
Autoconf
ment, if you want automatic IP assignment; select Static,
if you want to set the IP address manually; or DHCPv6.*
a. If you selected Autoconf, go to
DHCP Options.
On
or
Off
according to your preference.**
b. If you selected Static, go to
Address
IP address. Go to Gateway, and enter the gateway
address. Set
DHCPOptions
to
On
your preference.**
3.
Set DNS and NTP server addresses
If DHCP Options are switched off, you must set the DNS
and NTP server addresses in
Advanced configuration >
Network
1. Go to the
DNS
section and enter the DNS server
address in the
Server 1 Address
input field.
To set the NTP address, go to
Network services > NTP
and set the address. Select
save
to confirm the address.
Set
Mode
to Auto.
4.
Press
Home
(
) to return to the home menu.
** DHCP options:
On: The IP parameters, like the DNS and NTP server addresses, will be
obtained automatically from a DHCPv6 server.
Off: The IP parameters, like the DNS and NTP server addresses, must be
set manually.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
Contacts
and select
IPv6.
in the
IP assign-
Set to
and enter the
or
Off
according to