Cisco TelePresence SX20 Manuale introduttivo - Pagina 38

Sfoglia online o scarica il pdf Manuale introduttivo per Sistema di conferenze Cisco TelePresence SX20. Cisco TelePresence SX20 41. In-room control on touch 10
Anche per Cisco TelePresence SX20: Set rapido (8 pagine), Manuale introduttivo (42 pagine), Manuale di riferimento rapido (2 pagine), Set rapido (2 pagine), Manuale di riferimento rapido (2 pagine), Manuale d'uso (34 pagine), Manuale d'uso (29 pagine), Manuale di risoluzione dei problemi (37 pagine), Manuale di informazioni sulla conformità normativa e sulla sicurezza (9 pagine), Manuale di configurazione (8 pagine), Manuale d'uso (38 pagine), Manuale di installazione (2 pagine), Manuale d'uso (2 pagine), Manuale di riferimento rapido (2 pagine), Manuale d'uso (37 pagine), Manuale (45 pagine), Manuale (45 pagine), Scheda di installazione (2 pagine), Manuale di installazione (2 pagine), Manuale d'uso (34 pagine), Manuale d'uso (5 pagine), Manuale d'uso (38 pagine), Manuale d'uso (38 pagine), Manuale introduttivo (42 pagine), Manuale di riferimento (8 pagine), Manuale introduttivo (46 pagine)

Cisco TelePresence SX20 Manuale introduttivo
Cisco TelePresence Video Systems
Contents
The System Configuration page on
the web interface
You open the web interface by entering your video conference
system's IP address in the address bar of a web browser; then
you sign in.
When signed in, you can open the System Configuration page
from the Configuration menu.
You can access all configuration settings from this page.
All settings are not available on all products; therefore the folders
shown to the right may or may not be present on your system.
You can find a complete description of the web interface and
the settings in the administrator guide for your system.
D14639.12 Video Systems Getting Started Guide TC7.0, DECEMBER 2013.
Introduction
User interfaces
Configuration
The System configuration menu
The settings are arranged with the following top level categories:
Audio:
Settings for microphones, audio outputs, echo control, volume,
sounds, alerts, and more.
Cameras:
Settings for focus mode, brightness, whitebalance,
backlight compensation, options like flip and mirror, and more.
Conference:
Conference settings like transmit and receive bit rates,
bandwidth allocation, incoming call handling, encryption, packet loss
resilience and far end control.
Experimental:
Experimental settings are likely to change in future
releases. They can be used 'as is' and are not fully documented.
FacilityService:
e.g. Helpdesk.
GPIO:
Definition of the GPIO pins.
H323:
All H.323 protocol settings.
Logging:
Set logging mode (not applicable in this software version).
Network:
IP, VLAN and QoS settings.
NetworkPort:
Enable/disable the codec's second Ethernet port.
NetworkServices:
Telnet, SSH, HTTP, HTTPS, SNMP, H323, SIP and NTP.
Phonebook Server:
Provisioning:
Settings for provisioning mode, manager address and
protocols and methods.
RTP Port Range:
Security:
Settings for an audit server and error logging.
SerialPort:
Enable or disable the serial port, and set its baud rate.
SIP:
All settings for the SIP protocol.
Standby:
Configure when the system should enter standby and how
it should behave when entering/leaving standby mode.
SystemUnit:
Settings like system name and type, and menu language
selection.
Time:
Date and time settings.
User Interface:
Touch controller settings.
Video:
Settings for video sources and monitors, and video display
set-up and layout.
38
Getting Started Guide
Appendices
Appendices
Setting up speed dial buttons for facility services,
Enable/disable the network services: Multiway,
Phonebook type and location.
RTP port numbers.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
Contacts