Sony PICTURE STATION DPP-FP90 Leggete prima questo

Sfoglia online o scarica il pdf Leggete prima questo per Fotocamera digitale Sony PICTURE STATION DPP-FP90. Sony PICTURE STATION DPP-FP90 2. Digital photo printer
Anche per Sony PICTURE STATION DPP-FP90: Garanzia limitata (1 pagine), Opuscolo e specifiche (31 pagine), Manuale di servizio (27 pagine)

Stampa la pagina

Sony PICTURE STATION DPP-FP90 Leggete prima questo

DPP-FP70/FP90

Digital Photo Printer

Read This First

Welcome to the Sony Digital Photo Printer DPP-FP70/FP90.

Please read this side of this leafl et fi rst and follow the procedures to set up your printer: Inserting

the paper tray feeding print paper and ink ribbon makes your printer ready for printing.

After you fi nish setup, read the reverse side to print an image from a memory card.

You have now done the basic printing!

To enjoy a variety of printing or customize your printer, please read the operating instructions

also supplied.

Printed in China

3-097-070-12(1)

Learning about the printing process

Th e printer is a dye sublimation printer using an ink ribbon printing process.

As illustrated below, the ink ribbon is made up of three colored panels (yellow, magenta,

and cyan), and one clear lamination panel for overcoating.

When printing begins, the thermal print head heats up as it passes over the fi lm, causing

the dyes to vaporize and permeate the surface of the print paper. Aft er yellow, magenta,

and cyan have been laid onto the print paper, the fi nal cycle lays the laminate layer, which

protects the printed surface. Th ese four-panel printing cycles are required for each print.

An ink ribbon contains 40 sets of four panels. Aft er you print 40 sheets of print paper, the

ink ribbon also runs out.

Printing process ﬂ ow

Until printing fi nishes, yellow, magenta, cyan, and transparent laminate layers are

processed as follows:

The direction ink fi lm moves inside

the ink ribbon

Laminate fi lm

Cyan

Magenta

Yellow

Print Paper



Tip

During printing, print paper moves back and forth along the thermal head of the printer, which is why the print

paper is partially ejected several times from the rear and front paper outlets. Aft er the fi nal cycle of laminate layer

fi nishes, the print paper is ejected onto the paper tray.

Check the contents of the package.

Open the package and check to see that the following are contained.

(Illustrations used in this leafl et are of DPP-FP70. Th e button locations and names of

the DPP-FP90 are identical. )

Printer

AC adaptor

Paper tray

AC power cord

Cleaning cartridge/Cleaning sheet

(Used for cleaning inside the printer.)



Note

Th e AC power cord illustrated is for 120V

only. Th e plug shape and specifi cations of

the AC power cord diff er depending on the

region you purchased the printer.

• Operating Instructions

• Read Th is First (this leafl et)

• Warranty (In some regions, the warranty is not supplied.)

• Sony End User Soft ware License Agreement

• CD-ROM (Sony DPP-FP70/FP90 Printer Driver Soft ware Ver.1.0 and Picture

Motion Browser Ver.2.0)

Prepare an optional color print pack.

To print an image, you need a color print pack containing print paper and ink

ribbon.

Please use a Sony optional color print pack designed for the printer. Other types

of print packs may cause malfunctions.

Th e following print packs are available:

SVM-F40P

You can make 40 sheets of post card (4  6 inch/10  15 cm) size print. (One ink ribbon, 20-sheet-

pack  2)

20 sheets

of print paper

Ink ribbon for

40 prints

20 sheets

of print paper

SVM-F120P

You can make 120 sheets of post card (4  6 inch/10  15 cm) size print. (Th ree ink ribbons each

for 40 prints, 20-sheet-pack  6)

20 sheets

of print paper

Ink ribbon for

40 prints

20 sheets

of print paper

 3

Insert the print paper into the paper tray.

Check the printing surface of the print paper

Set the print paper with the printing surface facing up. Th e glossy surface

without imprints is the printing surface.

Reverse side

Printing surface



Notes

• Th e reverse side imprints design may be changed. Th e side with "Sony" logos is the reverse side.

• Do not touch the printing surface. Fingerprints on the printing surface may result in imperfect

printing.

• Do not bend the print paper, or cut the print paper from perforations before printing.

Open the paper tray cover.

Hold the parts on both sides of the paper tray cover (shown with arrows) and

open the paper tray cover.

Feeding direction

Set the print paper into the paper tray.

You can set up to 20 sheets of print paper.

Riffl e the print paper thoroughly. Th en insert the print paper into the arrow

direction with the protective sheet facing up. Th en remove the protective sheet.

If there is no protective sheet, insert the print paper with its printing surface (the

side with no imprint) facing up.

Protective sheet

(You cannot print on a

Protective sheet

protective sheet.)

Feeding direction



Note

Do not touch the printing surface.

Stretch out the slide cover of the paper tray cover if it is opened (), and then

close the paper tray cover ().

Slide cover

Keep the slide cover stretched out.

When you insert the paper tray into

the printer, the slide cover opens

automatically.

Paper holder



Note

Do not touch the paper holder of the paper tray. Otherwise the paper will not be fed correctly.

When storing the print paper in the paper tray

Remove the paper tray from the printer and shut the slide cover.

Note on number of sheets

With an ink ribbon, you can print the total of 40 sheets of the print paper, 2 packs of

20-sheet print paper.

When you feed the print paper, please make sure that the total number of sheets in the

paper tray does not exceed 20. When 2 packs of 20-sheet print paper runs out, the ink

ribbon should also run out.

20 sheets

of print paper

ink ribbon for

40 print

20 sheets

of print paper

Insert the paper tray and ink ribbon into the

printer.

Insert the paper tray containing the print paper and ink ribbon into the printer in

the following directions.

Inserting the paper tray into the printer

Pull and open the paper tray

compartment door.

Insert the paper tray into the printer.



Note

Please insert the paper tray straightly and fully into the printer until it fi ts into place. If the paper

tray is inserted at any angle, the printer may not print properly.

Setting the ink ribbon

Pull and open the ink ribbon

compartment door.

Insert the ink ribbon in the arrow

Arrow

direction until it clicks into place.

Close the ink ribbon compartment door.

Removing the ink ribbon

When the ink ribbon runs out, an message appears on the LCD screen of the

printer. Open the ink ribbon compartment door, push up the eject lever, and

remove the used ink ribbon.