Sony XCD-U100 Istruzioni per l'uso

Sfoglia online o scarica il pdf Istruzioni per l'uso per Fotocamera digitale Sony XCD-U100. Sony XCD-U100 2. Digital camera module
Anche per Sony XCD-U100: Manuale (4 pagine), Manuale tecnico (38 pagine), Manuale tecnico (39 pagine), Manuale di servizio (30 pagine)

Stampa la pagina

3-287-508-01 (1)

Digital Camera Module

Operating Instructions

お買い上げいただきありがとうございます。

XCD-V60CR/SX90CR/U100CR

(Color model)

XCD-V60/SX90/U100

(Black and white model)

 2007 Sony Corporation

Printed in Japan

3287508010

安全のための注意事項を守る。



故障したり破損したら使わずに、ソニーのサービス窓口に相談する。



警告表示の意味

注意を促す記号

行為を禁止する記号

行為を指示する記号

下記の注意を守らないと、

や

により

や

につながること

があります。

設置は確実に

レンズは確実に取り付ける

下記の注意事項を守らないと、

をしたり周辺の物品に

を与えることがあります。

内部に水や異物を入れない

分解しない、改造しない

カメラケーブルを傷つけない



指定された専用機器に接続する

指定された接続ケーブルを使う

Owner's Record

The model and serial numbers are located on the bottom. Record the

serial number in the space provided below. Refer to these numbers

whenever you call upon your Sony dealer regarding this product.

Model No. _____________

Serial No. ______________

WARNING

To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

IMPORTANT

The nameplate is located on the bottom.

Power Supply

The unit must always be operated with a 12V DC class 2 power supply.

In the USA, use a power supply which is UL Listed.

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own

expense.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

All interface cables used to connect peripherals must be shielded in

order to comply with the limits for a digital device pursuant to Subpart

B of Part 15 of FCC Rules.

For customers in Europe

This camera is not intended for use in security applications in the

meaning of the European standard series EN 50132 (Alarm systems -

CCTV surveillance systems for use in security applications).

For the customers in Europe

The manufacturer of this product is Sony Corporation, 1-7-1 Konan,

Minato-ku, Tokyo, Japan.

The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.

For any service or guarantee matters please refer to the addresses

given in separate service or guarantee documents.

This apparatus shall not be used in the residential area.

、



–1

/ Camera



–2

/ Camera





















日本語

　基本構成／ 

　オプションの構成



-1

-2



IEEE1394b





電源について

IEEE1394b

DC-700

使用・保管場所



お手入れ

XCD-V60CR/SX90CR/U100CR RAW

XCD-V60/SX90/U100

IEEE1394b

端子

800Mbps

高画質

CCD

XCD-V60CR/V60

VGA

XCD-SX90CR/SX90

UXGA

200

CCD

外部トリガー機能

電子シャッター

ピン

I/O

コネクター端子

IEEE1394b

I/O

低消費電力

XCD-V60CR/V60/SX90CR/SX90

XCD-U100CR/U100

3.0W DC 12V

筐体固定

CCD

白点

CCD



スミア現象

折り返しひずみ





 カメラモジュール

CCD

IEEE1394b

カメラケーブル（市販）



IEEE1394b

マウントレンズ（市販）



 カメラ用画像入力ボード（市販）

PCI

IEEE1394



800Mbps

 三脚アダプター

VCT-ST70I

 カメラアダプター

DC-700



 カメラケーブル

CCXC-12P02N

（

）（ソニー製）

/25N

25 m

 レンズマウント（

マウント

ご注意



 カメラ固定用補助穴（上面）

 カメラ固定用基準穴（底面）



ST70I

English

When Installing the Camera

When you install the camera with various peripheral devices and if the devices

have different ground electric potential, ground only one device. In case there

is an ground electric potential difference, the camera may be damaged.



-1

 IEEE1394b connector

 Host device (e.g., PC)



I/O

 Ground electric potencial difference





DC-700

Notes on Operation

Power supply

Power is supplied to the camera module via the IEEE1394b cable connected to a

PC. If the power supply is insufficient, use the DC-700/700CE that supplies stable

power with less ripple or noise.

Foreign bodies

Be careful not to spill liquids, or drop any flammable or metal objects in the

camera body.

Locations for operation and storage

0 40

Avoid operation or storage in the following places.



Extremely hot or cold locations. Recommended temperature range is 0°C to

40°C (32°F to 104°F)



Locations subject to strong vibration or shock



Near generators of strong electromagnetic radiation such as TV or radio

transmitters

Care

Use a blower to remove dust from the surface of the lens or optical filter. Clean

the exterior with a soft, dry cloth.

If the camera is very grimy, apply a cloth soaked in a mild detergent then wipe

with a dry cloth. Do not apply organic solvents such as alcohol which may

damage the finish.

Overview

The XCD-V60CR/SX90CR/U100CR is a color digital camera module that outputs

RGB Raw Data. The XCD-V60/SX90/U100 is a monochrome digital camera

module.

IEEE1394b

IEEE1394b connector

The camera module can output a digital image with a transfer speed of

800 Mbps. Two IEEE1394b connectors allow you to make up a daisy chain

connection.

CCD

High resolution

SXGA

125

CCD

The camera module uses a progressive scan CCD and produces high-resolution

XCD-U100CR/U100

and high-speed image output.

The XCD-V60CR/V60 has a CCD of 330,000 pixels (VGA) and outputs a digital

image at 90 frames per second. The XCD-SX90CR/SX90 has a CCD of 1,250,000

pixels (SXGA) and outputs at 30 frames per second. The XCD-U100CR/U100 has

a CCD of 2,000,000 pixels (UXGA) and outputs at 15 frames per second.

Because the CCDs are square pixel CCDs, you don't need to convert the aspect

ratio in your image processing.

External trigger function

You can operate the shutter at any timing by synchronizing the shutter with the

external trigger signals.

Electronic shutter

You can select the exposure time from a variety of settings. This allows you to

capture an image under optimal conditions.

12-pin I/O connector

When power from the IEEE1394b connector is insufficient, power is supplied

through the 12-pin connector. The 12-pin connector is also used for a trigger

input and strobe output, and as a general-purpose I/O port.

2.8W DC 12V

Low power consumption

The power consumption is decreased to 2.8 W for the XCD-V60CR/V60/SX90CR/

SX90 or 3.0 W for the XCD-U100CR/U100, with 12 V DC input.

Body fixing

The mounting screw holes are provided in the reference plane on the lower

surface of the body, allowing mounting with the absolute minimum deviation

of the optical axis.

Phenomena Specific to CCD Image Sensors

CCD

Charge Coupled Device

The following phenomena that may appear in images are specific to CCD (Charge

Coupled Device) image sensors. They do not indicate malfunctions.

White flecks

Although the CCD image sensors are produced with high-precision

technologies, fine white flecks may be generated on the screen in rare cases,

caused by cosmic rays, etc.

This is related to the principle of CCD image sensors and is not a malfunction.

The white flecks especially tend to be seen in the following cases:



when operating at a high environmental temperature



when you have raised the gain (sensitivity)



when using the slow shutter

Vertical smear

When an extremely bright object, such as a strong spotlight or flashlight, is

being shot, vertical tails may be produced on the screen, or the image may be

distorted.

Monitor screen

Aliasing

When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.

System Components

(





)

The camera module imaging system comprises the following products.

Products  to  are used for the basic configuration, and  to  for the

optional configuration. (All the products except the camera module are

available separately.)

 Camera module

This is a small-size, high-resolution, camera module using a CCD image sensor.

 IEEE1394b camera cable (commercially available)

Connect this cable to the IEEE1394b connector on the rear panel of the camera

module. The power and image/control signals are transmitted through this

cable. To prevent a poor connection or damage to the camera or cable, use the

cable equipped with fixing screws.

 C-mount lens (commercially available)

Use an appropriate lens for the camera module and usage.

 Camera module interface board (commercially available)

IEEE1394b

Install the board in a PCI bus slot of a host device such as a PC.

Select an IEEE1394 interface board to match your system.

（ソニー製）

Select an IEEE1394b interface board if you use the transfer speed of 800 Mbps.

 VCT-ST70I tripod adaptor (Sony)

Attach this adaptor to the bottom of the camera module to fix the camera

module to a tripod.

（ソニー製）

 DC-700/700CE camera adaptor (Sony)

Connect this adaptor to the camera module to enable power supply from an

ordinary AC power source.

（

2 m

）

/05N

（

5 m

）

/10N

（

10 m

）

 CCXC-12P02N (2 m, 6.6 ft)/05N (5 m, 16.4 ft)/10N (10 m, 32.8 ft)/

25N (25 m, 82 ft) camera cable (Sony)

I/O

Connect this cable to the 12-pin I/O connector on the rear panel of the camera

module. The cable is used for power supply and exchange of trigger signals.

Location and Function of Parts and Operation

Front/Top/Bottom

)

 Lens mount (C-mount)

Attach any C-mount lens or other optical equipment.

Note

10mm

The lens must not project more than 10 mm (13/32 inch) from the lens mount.

 Lens mount face

10mm



 Auxiliary holes (top)

 Reference holes (bottom)

These precision screw holes are for locking the camera module. Locking the

camera module into these holes secures the optical axis alignment.

For details, refer to the Technical Manual.

Four screw reference holes  can be used as the tripod adapor screw holes,

too. Screw the VCT-ST70I tripod adaptor into the four screw holes when you use

a tripod.

VCT-

Fig. A

Basic configuration / 

-2

Optional configuration

 12-pin I/O connector

 Abnormal electricity

 Power supply unit (DC-700/700CE)

Vertical tails shown

on the image

Bright object

(e.g. strong spotlight,

strong reflected light,

flashlight, the sun)

Fig. B

Fig. C

 10 mm (13/32 inch) or less

(continued on the reverse side)