Digitool Solutions DWA-1002 Manuale d'uso

Sfoglia online o scarica il pdf Manuale d'uso per Utensile elettrico Digitool Solutions DWA-1002. Digitool Solutions DWA-1002 2. Electronic torque angle wrench

Stampa la pagina

Specifications:

Model

Range

Square Drive

DWA-2501

250.0 in-lb

1/4inch

DWA-1002

100.0 ft-lb

3/8 inch

DWA-2503

250.0 ft-lb

1/2 inch

Display

5-digit, alpha-numeric LCD with function and

battery indicator icons.

Accuracy

Torque: within ±1% of Indicated Value of both CW

and CCW directions. (10%-100% of F.S)

Angle: within ± 1° when rotating to 90° at the

speed rate @ 2°/s to 400°/s

Calibration:

should be performed once a year or every

15,000 cycles which ever comes first.

Resolution:

Units of measure

ft-lb, in-lb, Nm

Model

Drive

ft-lb

DWA-2501

1/4 inch

0.01 ft-lb

DWA-1002

3/8 inch

0.1 ft-lb

DWA-2503

1/2 inch

0.2 ft-lb

Modes of measure:

Peak Hold, Angle

Measurement Modes:

ANGLE- 15 seconds display of peak Angle.

Minimum 5% of full scale torque apply before Angle

start measurement.

Example: Model DWA-1002 full scale is 100ft-lb

5% of F.S is 5 ft-lb. when torque reached

Above 5 ft-lb. Angle will start measure.

TORQUE - Display torque value in real time when torque is

loading and display peak torque when released

Visual, Audible Alerts:

Yellow LED and buzzer pulse at 80% - 96% of target torque.

Pulse rate increases as target torque is approached.

Green LED and buzzer on continuously when applied torque

is within 96% - 104% of target torque.

Red

LED and buzzer on continuously when applied torque

exceeds >104% target torque or wrench full-scale.

Tactile Vibration when applied torque is within ±4% of

target torque.

Battery Power:

2 AA battery up to 200 hours of continuous operation

Weight

Certification:

1.5 pound

This device is calibrated at the factory and is certified to meet

2.2 pound

International Standards. ISO-6789-2003 and ASME B107-28-

3.4 pound

2005 standards compliant. Certificate of N.I.S.T. (National

Institute of Standards Technology). Traceability from 10% to

100% of full scale

Maintenance:

To clean the wrench, wipe with a lightly dampened cloth.

DO NOT use: solvents, thinners or engine cleaners. DO NOT

immerse in any liquids.

Torque & Angle Wrench be calibrated once a year or every

15,000 cycles, whichever comes first. Contact Digitool Solutions

representatives for repair and calibration services.

Warranty Service and Recalibration

in-lb

Digitool Solutions provides a 1 year warranty that covers any

Digital Torque & Angle Wrench which fails to give satisfactory

0.1 in-lb

0.01 Nm

service due to defective workmanship or materials (excluding

calibration) for 12 months from the date of original purchase.

1 in-lb

0.2 Nm

Calibration is only covered by this warranty for each new unused

Torque & Angle Wrench out of box. Products must be returned

1 in-lb

0.3 Nm

with proof of purchase, freight prepaid, to the warranty service

center listed below.

This warranty excludes Torque & Angle Wrench that have been

subjected to abnormal use, accidental damage, neglect, or lack of

maintenance. Any modification or disassembly of this Torque &

Angle Wrench or repair by an unauthorized service center will

void the warranty. This warranty gives you specific rights. You

may also have other rights which vary from state to state. The

foregoing obligation is Digitool Solutions sole liability under this or

any implied warranty and under no circumstances shall Digitool

Solutions be liable for any incidental or consequential damages.

Note: Some states do not allow the exclusion or limitation of

incidental or consequential damages so the above limitation or

exclusion may not apply to you.

For Warranty Service and Recalibration/Certification

Services, contact:

It is highly recommended that your

Digitool Solutions LLC,.

13905 Ramona Ave. Unit #A

Chino, CA 91710

Phone: (909)591-9581

Fax (909) 233-6491

Website: digitoolsolutions.com

ELECTRONIC TORQUE ANGLE

WRENCH

TORQUE, ANGLE INDICATOR

For Models

DWA-2501, DWA-1002,

DWA-2503

USER'S GUIDE

Ratchet head:

1/4" , 3/8" or 1/2" drive 36 teeth

Accuracy:

Torque. ±1% CW & CCW

From 10%-100% of Full scale

Angle. ±1° of 90° rotation

@ speed rate 2°/s - 400°/s

Display:

5-digit, alpha-numeric LCD

With functions, units and

battery indicator icons.

Indicators:

LED Green, Yellow and Red

Buzzer, Vibrator

Power:

Manual/Auto shut off after

5 minutes Idle

Battery:

2 AA size Battery Regular Alkaline

up to 200 hours of continuous operation

Rev.Dec. 2014