Digitrax DN163A3 Manuale - Pagina 7

Sfoglia online o scarica il pdf Manuale per Convertitore multimediale Digitrax DN163A3. Digitrax DN163A3 12.

O O t t h h e e r r L L o o c c o o M M o o t t i i o o n n ™ F F e e a a t t u u r r e e s s : : S S w w i i t t c c h h i i n n g g S S p p e e e e d d , , N N o o r r m m a a l l D D i i r r e e c c t t i i o o n n o o f f

T T r r a a v v e e l l & & S S c c a a l l e e a a b b l l e e S S p p e e e e d d S S t t a a b b i i l l i i z z a a t t i i o o n n ( ( B B a a c c k k E E M M F F ) ) F F e e a a t t u u r r e e s s

Switching speed is controlled by CV54. The factory setting is 000/x00 for

OFF. To turn on the switching speed feature, program CV54 to a value of

001/x01. When this feature is on, use F6 to activate and deactivate switching

speed. When switching speed is ON and F6 is ON, the switching speed feature

is on. With the feature ON, the throttle's target speed is effectively reduced by

about 50% and the effects of accel and decel programmed into the decoder are

reduced by 1/4. This is useful for yard switching operations.

Normal Direction of Travel is controlled by CV29. See your decoder manual

for additional information on the settings for CV29.

The intensity, or droop, of Scaleable Speed Stabilization (Back EMF) is con-

trolled by CV57. The factory setting for this feature is 006/x06 which is suit-

able for most locos. You can adjust this value in the range of 000/x00 for OFF

to 015/x0F for the maximum effect. Consult your Digitrax Decoder Manual for

info about CVs 55 & 56 and their effects on scaleable speed stabilization.

S S u u p p e e r r S S o o n n i i c c ™ S S i i l l e e n n t t O O p p e e r r a a t t i i o o n n a a n n d d T T o o r r q q u u e e C C o o m m p p e e n n s s a a t t i i o o n n

The factory settings in the decoder provide silent, smooth operation of your

locomotive under most conditions. For more information about these settings,

please see the Digitrax Decoder Manual or our website.

D D i i g g i i t t r r a a x x T T r r a a n n s s p p o o n n d d i i n n g g C C V V 6 6 1 1

Digitrax Transponding is controlled by CV61. The initial factory set value is

Loco Type

Switcher

Concentrated low speed. Limited top

speed

Road Switcher

Prototypical top speed w/evenly

distributed curve from 0 to top speed

Mainline Loco

Quick increase to cruising speed then

levels off to prototypical top speed.

000/x00 for OFF. To turn ON transponding, program CV61 to a value of

002/x02. This allows you to use Digitrax transponding to keep track of your

rolling stock. When transponding is enabled, the front light of the locomotive

will flicker slightly to indicate transponding signal is being communicated. For

optimal transponding operation, we recommend that you hook up the forward

and rear lights as shown in the wiring diagram (Figure 1).

4 4 5 5 0 0 C C e e m m e e t t e e r r y y S S t t r r e e e e t t

N N o o r r c c r r o o s s s s , , G G A A U U S S A A 3 3 0 0 0 0 7 7 1 1

w w w w w w . . d d i i g g i i t t r r a a x x . . c c o o m m

V Start

CV02

002/x02

www.digitrax.com

7 7 7 7 0 0 - - 4 4 4 4 1 1 - - 7 7 9 9 9 9 2 2

T T

7 7 7 7 0 0 - - 4 4 4 4 1 1 - - 0 0 7 7 5 5 9 9

F F

s s a a l l e e s s @ @ d d i i g g i i t t r r a a x x . . c c o o m m

E E

V Mid

V Max

CV06

CV05

038/x26

064/x50

048/x30

098/x62

128/x80

154/x9A