Argonaut A615 SMFD Manuale d'uso - Pagina 4

Sfoglia online o scarica il pdf Manuale d'uso per Monitor Argonaut A615 SMFD. Argonaut A615 SMFD 20. Smart multi function display

Stampa la pagina

attach to 8 corresponding mount plate holes. Tighten screws such that tips are about flush with the

mount back edge surface (note: further adjustment tightening will be done in steps listed below).

5) Allow display assembly to drop back into cutout hole such that the screw heads are flush to the

front mounting surface. Carefully tighten front surface screws an equal amount to pull display up

to a perfectly aligned "flush position with outside front surface.

6) Screw 4 back adjustment screws against the back of the mounting surface to firmly secure the

display in place.

7) Pull off adhesive liner from face plate and carefully attach to display front and surface opening.

Optional RAM Or U-Bracket Mount

The RAM mount includes surface base, swivel arm, display mounting base plate and screws/washers.

Secure square display mounting base plate to back of display using four stainless steel 10/32 x ½" screws

(in order from base, flat washer, split washer, screw). Note: RAM logo should be oriented upside down

for optimal position. Securely tighten but do not over tighten. Attach circular RAM base to mounting

location. Secure display with swivel arm to surface.

U-Bracket mount includes 2 aluminum U brackets, and 2 adjustment/mounting knobs. Locate suitable

mounting location for U bracket mount base. Attach base to mounting surface with 4 bolts and backing

washers/nuts. Place display within mounted base bracket and secure with side knobs.

Wiring

NOTE: THE POSITIVE WIRE IS RED AND THE NEGATIVE WIRE IS BLACK.

The standard input cables include 2 x USB, DVI, RCA/S-Video, and DC Power cable. If optionally

equipped with HDMI, note that this is an HDMI output signal which will output a duplicate image of your

Android screen. All cables exit the rear of the display through a waterproof cable clamp. Note that the

cable ends are not waterproof and should be placed or installed in a dry, protected area. DO NOT

PULL CABLES TIGHT TO PREVENT EXCESS STRAIN AND POSSIBLE BREAK IN CABLE

CLAMP SEAL. Contact your Argonaut Dealer if additional cable lengths are required in excess of

standard provided.

Power

The A615 SMFD is designed for 12 Volt power input through an Argonaut supplied power regulator. The

correct regulator should be specified at time of ordering for connection to either a 12 volt or 24 volt system.

The regulators accept a range of voltage (either 9 to 18V or 19 to 32V) and provide a steady 12 volts to the

display.

NOTE: ANY DIRECT CONNECTION OF THE DISPLAY TO 12 OR 24 VOLT POWER

WITHOUT FIRST RUNNING THROUGH THE ARGONAUT SUPPLIED REGULATOR COULD

PERMANENTLY DAMAGE THE DISPLAY AND VOID YOUR WARRANTY. DO NOT

CONNECT THE REGULATOR TO VOLTAGE EXCEEDING THE SPECIFIED RANGE AS

THIS WILL DAMAGE THE REGULATOR. DO NOT CONNECT THE DISPLAY DIRECTLY

TO A/C POWER (110-220V) POWER AS THIS WILL DAMAGE THE DISPLAY AND COULD

CAUSE A FIRE.

PLEASE MAKE SURE TO AVOID IMPROPER CROSSING WIRES

(POSITIVE TO NEGATIVE) AS THIS CAN DAMAGE THE DISPLAY ELECTRONICS.

Care & Precautions

Care: The LCD has an optically bonded anti-reflective glass overlay for optimal sunlight visibility. Clean

with soft clean cloth dampened with fresh water to remove residue. Follow up with alcohol and lens

cleaning wipes if desired. If water has collected in screen bezel, wipe dry before covering/storing. NOTE:

DO NOT ALLOW SALT WATER DEPOSITS TO REMAIN ON GLASS SURFACE FOR

EXTENDED PERIODS (REMOVE SALT DEPOSITS WITH FRESH WATER). LONG TERM

SALT DEPOSITS MAY CAUSE PERMANENT DAMAGE TO THE SCREEN SURFACE.

Additional Precautions: Do not operate in temperature extremes (below 32°F (0° C) or above 104 °F

(40° C)). Do not put pressure or contact directly on screen surface. Do not connect directly to power

source without using the regulator supplied. Do not reverse power wires. Do not expose to

Page