Epson FX-880+ Manuale - Pagina 15

Sfoglia online o scarica il pdf Manuale per Accessori per stampanti Epson FX-880+. Epson FX-880+ 18. Epson serial impact dot matrix printers
Anche per Epson FX-880+: Manuale di configurazione (33 pagine), Opuscolo e specifiche (24 pagine), Specifiche tecniche (2 pagine), Leggete prima questo (2 pagine), Manuale di riferimento (34 pagine), Manuale rapido (33 pagine)

Stampa la pagina

To turn Lock-out mode off, repeat steps 1 and 2. The printer

beeps once, indicating that the Lock-out mode has been turned

off.

Changing the Lock-out mode setting

You can select which printer functions you want to be locked

while Lock-out mode is on. Follow these steps:

1. Make sure paper is loaded and the printer is turned off.

2. Turn on the printer while holding down the

buttons. The printer enters the Lock-out setting

Pause

mode and prints the instructions. (You'll need three sheets

of A4 or letter size single-sheet paper or three pages of

continuous paper that is at least 11 inches [279 mm] long

and 8.3 inches [210 mm] wide.)

3. Follow the instructions to change the settings as desired.

4. Turn off the printer.

See the instructions above to turn on Lock-out mode after you

change the Lock-out mode setting.

Emulating the Okidata Microline 320

Turbo

If you have the EPSON FX-880+, you can make it work like

the Okidata

Microline

320 Turbo by turning the printer on

in a different mode. In this mode, the printer emulates Okidata

functions, including the following. Default settings are bold.

EPSON FX-880+ in

Feature

Okidata mode

Software emulation

IBM

ESC/P

Printable area

Top margin

22 mm

Bottom margin

24 mm

Line spacing (lines per

6 LPI, 8 LPI

inch)

Paper out override

Off, On

* As measured by EPSON.

If you want to use your printer in Okidata mode, do not

install the Windows driver that came with your

FX-880+. If you have been using an Okidata driver, you

can continue to use it with your FX-880+ in Okidata

mode.

To enter Okidata mode, make sure the printer is turned off.

Then hold down the

Tear Off/Bin

you turn on the printer. The printer beeps once. Now turn the

printer off, wait 5 seconds, and turn it back on (with just the

power switch) to begin using it in Okidata mode.

LF/FF

Okidata ML320

Turbo

PPDS, EPSON

IBM ProPrinter III,

, Oki ML 320T

EPSON ESC/P, Oki

ML 320T

22 mm *

24 mm *

6 LPI, 8 LPI

Off, On

and

buttons while

Pause

The printer remains in Okidata mode until you repeat the

above procedure. To return to FX-880+ mode, hold down the

Tear Off/Bin

The printer beeps twice. Turn it off, wait 5 seconds, and then

turn it back on to begin using the printer in FX-880+ mode.

and

Aligning Vertical Lines in Your

Printout

If you notice that the vertical lines in your printout are not

properly aligned, you can use the printer's bidirectional

adjustment mode to correct this problem. During bidirectional

adjustment, the printer prints three sheets of alignment

patterns, labeled High Speed Draft, Draft, and NLQ (near

letter quality). You select the best alignment pattern from each

sheet.

To print the instruction sheet and alignment patterns, you need

five single sheets or five pages of continuous paper of at least the

following sizes:

Paper type

Continuous paper (including

perforated border)

Single sheet

If you use single sheets, you need to load a new sheet of paper

each time the printer ejects a printed sheet from the paper

guide.

Follow these steps to perform the bidirectional adjustment:

1. Make sure paper is loaded, then turn off the printer.

2. While holding down the

The printer enters the bidirectional adjustment mode and

then prints instructions and the first set of alignment

patterns.

3. As described in the instructions, compare the alignment

patterns and select the pattern with the best alignment.

Then select the pattern with the best alignment for each of

the remaining sets of alignment patterns.

4. After you select the best pattern in the final set of alignment

patterns, save your selection by turning off the printer.

10/01

EPSON FX-880+/FX-1180+

and

buttons while you turn on the printer.

Pause

You can print the default settings for the printer when it

is in Okidata mode to check the current settings and

change them if necessary. See "Changing default

settings" on page 14.

FX-880+

9.5

11 inches

(241

279 mm)

A4 or letter size

button, turn on the printer.

Pause

EPSON FX-880+/FX-1180+

FX-1180+

14.8

11 inches

(376

279 mm)

A3 landscape