Motorola GM950 Manuale - Pagina 9

Sfoglia online o scarica il pdf Manuale per Radio Motorola GM950. Motorola GM950 18. Remote mount kit
Anche per Motorola GM950: Manuale d'uso (9 pagine), Manuale d'uso (11 pagine), Manuale (16 pagine), Manuale (18 pagine), Manuale di installazione (10 pagine)

Stampa la pagina
Motorola GM950 Manuale
3.6

Keypad and Top Keys

The HHCM keypad has 10 keys, plus 3 additional keys, the on/off key being one of them, which are
located on the top of the HHCM.
All keys are configured as 3 analogue lines (ANALOG 1 2 3) to the radio. Each of the lines controls
four keys; line ANALOG 3 additionally controls the on / off key. The voltage on the analogue lines
varies between 0V and +5V depending on which key has been pressed. If a button is pressed, it will
connect one of the 3 lines ANALOG 1,2,3 to a resistive voltage divider connected to +5V. The
voltages of these lines are A/D converted inside the µP and specify the pressed button.
3.7

Switch Functions

Ten of the switches (PB0931 - PB0934, PB0941 - PB0944, PB0953, PB0954) are the keypad
switches. The remaining 3 Top Key switches (PB0951, PB0952, PB0971) and the PTT switch
(PB0901) are simple contact closure switches. The switches and their functions are detailed below:
Switch
PB0901
PB0931
PB0932
PB0933
PB0934
PB0941
PB0942
PB0943
PB0944
PB0951
PB0952
PB0953
PB0954
PB0971
3.8

Status LED and Back Light Circuit

All the indicator LEDs (3) and the back light LEDs (10) are driven by current sources Q0982 - Q0986
and controlled by the µP via SERIAL PERIPHERAL INTERFACE (SPI). The current is determined
by the resistor at the emitter of the respective current source transistor. Shiftregister U0983 stores
the LED status. To update the LED status line LED CLCK BUF shifts the data of line SPI DATA BUF
into the shiftregister. When all the data has been written, line LED CE is set to low for a few
microseconds to update the output of the shiftregister with the new data.
The green (D0983), red (D0982) and yellow (D0981) indicator LEDs are covered by the LCD display.
If a LED is switched on, the corresponding area of the LCD display is switched to transparent by the
respective shiftregister output using Exclusive-OR (XOR) gate U0982-1-4 and the backplane signal
from the LCD driver U0981 pin 26, 27.
The squarewave backplane signal from U0981 is buffered by XOR gate U0982-1 and then fed to one
of each inputs of the three remaining XOR gates. The output of these gates is the inverted
backplane signal, while the connected output of the shiftregister is high, and non-inverted while it is
low. The inverted backplane signal fed to the respective LCD input makes the corresponding area
transparent for the covered LED, while a non - inverted backplane signal makes it non-transparent.
Introduction/Theory of Operation
Type
Function
Contact
PTT
Keypad
Configurable
Keypad
Configurable
Keypad
Configurable
Keypad
Configurable
Keypad
Volume Down
Keypad
Volume Up
Keypad
Configurable
Keypad
Configurable
Contact
Configurable
Contact
Configurable
Keypad
Scroll Down
Keypad
Scroll Up
Contact
Power ON/OFF
Theory of Operation
4C.1-3