Toshiba 16SAVR Series Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Condizionatore d'aria Toshiba 16SAVR Series. Toshiba 16SAVR Series 4.

Stampa la pagina

TEMPORARY OPERATION

In case of the misplaced or discharged remote control

• Pressing the RESET button, the unit can start or

stop without using the remote control.

• Operation mode is set on AUTOMATIC operation,

preset temperature is 24°C and fan operation is

automatic speed.

TIMER OPERATION

Setting the ON Timer

Press

: Set the desired ON timer.

SET

Press

: Set the timer.

CLR

Press

: Cancel the timer.

Daily timer allows the user to set both the ON & OFF timers and will be

activated on a daily basis.

Setting Daily Timer

Press

: Set the ON timer.

Press

OFF

: Set the OFF timer.

• During the daily timer is activating, both arrows ( , ) are indicated.

Note:

• Keep the remote control in accessible transmission to the indoor unit;

otherwise, the time lag of up to 15 minutes will occur.

• The setting will be saved for the next same operation.

PRESET OPERATION

Set your preferred operation for future use. The setting will be memorized by

the unit for future operation (except airﬂ ow direction).

1. Select your preferred operation.

PRESET

2. Press and hold

for 3 seconds to memorize the setting.

The P mark displays.

PRESET

3. Press

: Operate the preset operation.

AUTO RESTART OPERATION

To automatically restart the conditioner after the power failure (Power of the

unit must be on.)

Setting

1. Press and hold the RESET button on the indoor unit for 3 seconds to set

the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for

5 seconds)

• Do not operate ON timer and OFF timer.

2. Press and hold the RESET button on the indoor unit for 3 seconds to

cancel the operation. (3 beep sound but OPERATION lamp does not

blink)

QUIET OPERATION

To operate at super low fan speed for quiet operation (except in DRY mode)

QUIET

Press

: Start and stop the operation.

Note: Under certain conditions, QUIET operation may not provide

adequate cooling or heating due to low sound features.

COMFORT SLEEP OPERATION

To save energy while sleeping, automatically control air ﬂ ow and

automatically turn OFF.

COMFORT

SLEEP

Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note: The cooling operation, the set temperature will increase

automatically 1 degree/hour for 2 hours (maximum 2 degrees

increase). For heating operation, the set temperature will

decrease.

SLEEP TIMER OPERATION

To start the sleep timer (OFF timer) operation

Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

SLEEP

1110250162_EN.indd 3

Setting the OFF Timer

Press

OFF

: Set the desired OFF timer.

SET

Press

: Set the timer.

CLR

Press

: Cancel the timer.

Press

SET

Press

button during the

( or ) mark ﬂ ashing.

MAINTENANCE

Firstly, turn off the circuit breaker.

Filter Reset (Some models only)

FILTER lamp lights on; the ﬁ lter must be cleaned.

To turn off the lamp, push the RESET button on the indoor unit or the FILTER

button on the remote control.

Indoor Unit and Remote Control

• Clean the indoor unit and the remote control with a wet cloth when

needed.

• No benzine, thinner, polishing powder or chemically-treated duster.

SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)

To protect bad smell caused by the humidity in the indoor unit.

1. If the

button is pressed once during "Cool" or "Dry" mode, the fan will

continue to run for other 20 minutes, then it will turn off automatically.

This will reduce the moisture in the indoor unit.

2. To stop the unit immediately, press the

Note:

• SELF CLEANING operation is default setting from factory.

• To cancel this function, press and hold the reset button on the indoor

unit for 20 seconds.

The SELF CLEANING operation will be cancelled. (5 beep sound but

OPERATION lamp does not blink)

• Do the same to set this function again. (5 beep sound and OPERATION

lamp blink 5 time/sec for 5 seconds)

• AUTO RESTART operation will be cancelled by setting or cancellation of

SELF CLEANING operation. Set it again if necessary.

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated

for 3 minutes when suddenly restarted or switched to ON.

2. Preheating operation: Warm up the unit for 5 minutes before the heating

operation starts.

3. Warm air control: When the room temperature reaches the set

temperature, the fan speed is automatically reduced and the outdoor

unit will stop.

4. Automatic defrosting: Fans will stop during defrost operation.

5. Heating capacity: Heat is absorbed from outdoors and released into

the room. When the outdoor temperature is too low, use another

recommended heating apparatus in combination with the air conditioner.

6. Consideration for accumulated snow: Select the position for outdoor unit

where it will not be subjected to snow drifts, accumulation of leaves or

other seasonal debris.

7. Some minor cracking sound may occur when unit operating. This is

normal because the cracking sound may be caused by expansion/

contraction of plastic.

Note: Item 2 to 6 for Heating model

Air conditioner operating conditions

Temp.

Outdoor Temperature

Operation

Heating

–15°C ~ 24°C

Cooling

–10°C ~ 46°C

Dry

–10°C ~ 46°C

TROUBLESHOOTING (CHECK POINT)

The unit does not operate.

Cooling or Heating is abnormally low.

• The power main switch is

• The ﬁ lters are blocked with dust.

turned off.

• The temperature has been set improperly.

• The circuit breaker is

• The windows or doors are opened.

activated to cut off the power

• The air inlet or outlet of the outdoor

supply.

unit is blocked.

• Stoppage of electric current

• The fan speed is too low.

• ON timer is set.

• The operation mode is FAN or DRY.

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air

conditioner are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold CHK ● button on the Remote Control by the tip of the

pencil. "00" will be shown on the display.

MODE

during pushing CHK ● . "B" will show on the display and

4. Press

"00" will disappear and the air conditioner will turn OFF. The Remote

Control B is memorized.

Note: 1. Repeat above step to reset Remote

Control to be A.

2. Remote Control A has not "A" display.

3. Default setting of Remote Control from

factory is A.

3 times within 30 seconds.

Room

Temperature

Less than 28°C

21°C ~ 32°C

17°C ~ 32°C

5/7/09 3:37:11 PM