Toshiba TDP-T90 Manuale d'uso - Pagina 11

Sfoglia online o scarica il pdf Manuale d'uso per Proiettore Toshiba TDP-T90. Toshiba TDP-T90 25. Dlp data projector 2000 ansi lumens
Anche per Toshiba TDP-T90: Specifiche tecniche (2 pagine)

Stampa la pagina

Placement

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

The factory setting is "floor-mounted front projection." Set the Projection mode in the

default setting menu

p.32

, in accordance with your needs.

Floor-mounted front projection

Ceiling-mounted front projection

WARNING

• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.

Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus

resulting in injury.

• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the

projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.

Improper mounting could cause the projector to fall, resulting in an accident.

• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let

everyone involved with the use of the projector know that fact.

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection distance.

(Projection sizes are approximate values for full-size picture with no keystone adjustment.)

As seen from above

Screen

As seen from the side

Lens center

a is the distance (m) between the lens and the

screen, and corresponds to a range of 1.20 m to

10.00 m. H is the height from the image bottom to

the center of the lens.

Floor-mounted rear projection

Ceiling-mounted rear projection

a (min length) = projection size (inches) × 4.064

a (max length) = projection size (inches) × 4.878

projection distance a (m)

projection

height (H)

min length

max length

size (inches)

(zooming max) (zooming min)

24.6

—

1.20

1.62

1.95

2.44

2.93

3.25

3.90

100

4.00

4.88

150

6.10

7.30

200

8.10

9.76

246

10.00

—

Connection

Before connection

• Read the owner's manual of the device you are connecting to the projector.

• Some types of computer cannot be used or connected to this projector.

Check for an RGB output terminal, supported signal

• Turn off the power of both devices before connecting.

• The figure below is a sample connection. This does not mean that all of these devices

can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)

Computer (for control)

To audio output

To RS-232C

White (L)/Red (R)

p.47

terminal

Control cable

Audio cable

RGB cable

(not supplied)

To RGB

output

To audio

output

Computer

DVD video recorder, etc.

(cm)

5.6

9.1

Notes

13.8

18.3

• COMPUTER terminals 1 and 2 function identically.

22.9

• For TDP-T91, the document camera should be connected to COMPUTER terminal 2.

34.3

• The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.

45.7

56.2

p.45

, etc.

Video recorder,

VCR

DVD player, etc.

To video

To audio output

To S-Video

output

White (L)/Red (R)

output

Video cable (not supplied)

AV cable

S-Video cable

(not supplied)

Monitor cable Mini

D-sub 15P-BNC

RGB cable

(not supplied)

(supplied with

TDP-T91)

To Y/C

output

Green (Y)/Blue (C

)/Red (C

)

Conversion adapter BNC-pin

(not supplied)

Document camera

Audio amplifier, etc.

To audio input

Audio cable

White (L)/Red (R)

(not supplied)

RGB cable

Audio cable

(supplied)

(not supplied)

To audio output

To RGB output

Computer