Toshiba XE30U - TLP XGA LCD Projector Manuale d'uso - Pagina 13
Sfoglia online o scarica il pdf Manuale d'uso per Proiettore Toshiba XE30U - TLP XGA LCD Projector. Toshiba XE30U - TLP XGA LCD Projector 28. Mobile projector
Anche per Toshiba XE30U - TLP XGA LCD Projector: Specifiche tecniche (2 pagine), Specifiche di dettaglio (2 pagine)
Stampa la pagina
Turning the power on and off (Continued)
Notes
• The start-up screen will disappear after a moment. You can dismiss the start-up screen
before this by performing any operation. You can also configure the system to prevent the
start-up screen from appearing. To do this, use the Display setting menu
• The first time you use the projector after purchase, after the start-up screen disappears,
the start menu is displayed
.
p.25
• Beep sound can be set not to beep in the Default setting 1 menu
• When [Key lock] is [On], the operation buttons of the projector do not work
• When [Password setting] is [On], then the start-up screen is displayed after the
Password entry screen disappears
p.31
■ Turning the power off
1
Press the ON/STANDBY button.
A message appears on the screen, confirming that you wish to shut off the power. This
message will disappear after a moment. (This operation is no longer valid after the
message disappears.)
2
Press the ON/STANDBY button once again.
When the setting of beep sound is [On], the projector beeps, and the screen turns off,
but the internal cooling fan continues to operate. Then, the projector goes into standby
mode.
During cooling, the ON/STANDBY indicator flashes. While the
indicator is flashing, the power can not be turned back on. At this
point of time, it does not matter even if you unplug the power
cord.
Note
• The projector consumes about 10W of power in standby. We recommend that you unplug
the power cord if you will not be using the projector for an extended period.
PRECAUTION
• If you turn the power on before cooling is complete, give the lamp time (about 5 minutes)
to cool before plugging it back in. If the lamp overheats, it may fail to light.
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions.
• In order to extend the lifetime of the LCD panel, always turn off the power when not in
use, and make sure that the lamp is off. Keeping the lamp off is also very effective at
saving electricity.
• If the air filter becomes dirty and clogged, the projector's internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. Clean the air filter
from time to time
p.46
, and replace it periodically. Contact the store where you
purchased your projector, or your local Service Station for replacement air filters.
p.37
.
p.40
.
p.41
.
24
Basic operations
1
Turn on the power.
Turn on the power by following the instructions in "Turning the power on"
2
Select the language (When using the first time).
When the projector is used for the first time after purchase, the start menu for lan-
guage (to display the menus and messages on the screen) selection is displayed in
English. (If the screen is out of focus, adjust it according to the step
.
Use the
language and press the
Message for setup confirmation is displayed in a
selected language.
Notes
• When the projector is turned on the next time, the start menu does not appear upon
startup. However, if [Reset all] is executed from the Default setting 2 menu
the start menu will be displayed the next time when the power is turned on.
• The language can also be set via the Display setting menu
• This owner's manual assumes that English has been selected.
3
Activate the connected device.
Turn on and start the connected device such as a computer.
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
Notes
• When [Auto input search] is set to [Off] in the Default setting 1 menu
setting is [On]), the Input select menu appears if you press the INPUT button.
• If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and "There is no other input signal." will appear.
or
button to select the desired
button.
25
p.23
.
.)
6
English
French
German
Italian
Spanish
Portuguese
Russian
Swedish
Turkish
Polish
Japanese
Chinese (simplified)
Chinese (traditional)
Korean
,
p.41
.
p.37
(factory
p.40