Aries Offroad S226008-2 Istruzioni per l'installazione

Sfoglia online o scarica il pdf Istruzioni per l'installazione per Automobile Accessories Aries Offroad S226008-2. Aries Offroad S226008-2 2.

Stampa la pagina

PARTS LIST:

1 Driver/Left Sidebar

1 Passenger/Right Sidebar

1 Driver/Left Front Mounting Bracket

1 Passenger/Right Front Mounting Bracket

1 Driver/Left Front Frame Bracket

1 Passenger/Right Front Frame Bracket

1 Driver/Left Rear Mounting Bracket

1 Passenger/Right Rear Mounting Bracket

2 12mm x 50mm Bolt Plates

2 12mm x 40mm Bolt Plates (square end)

2 10mm x 40mm Bolt Plates (rounded end)

4 12mm Lock Washers

Passenger Side Rear

Mounting Bracket

Passenger Side Front

Mounting Bracket

Front

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ

INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.

Starting on the driver side front of the vehicle, locate the round hole on the bottom of the inner frame channel. Insert the

10mm round End Bolt Plate into the hole and rotate clock-wise 90-degress or until it stops turning,

Next, locate the two threaded holes, one located on the bottom of the floor rocker pannel, the other located on the side of

the inner rocker pannel. Position the driver side Front Mounting Brackets up to vechile. Hang the mount bracket from the

two holes using the provided (2) 8mm x 25mm Hex Bolts, (2) 8mm Flat Washers and the 8mm lock Washers. Snug but

do not tighten at this time,

4. Determine the driver side Front Frame Bracket fr

Front Mounting Bracket and bolt together with (2) 10mm x 35mm Hex Bolts (4) 10mm x 26mm OD Flat Washers and (2)

10mm Lock Nuts. Next hang the Support Bracket from the previously installed Bolt Plate using (1) 10mm x 26mm OD Flat

Washer, (1) 10mm Lock Washer and (1) nut,

Next, move to the driver/left rear of the vehicle. Insert the 12mm Bolt Plate into the oval hole located on the bottom of the

frame channel and rotate 90-degrees,

hole located on the bottom of the body next to the pinch weld. Rotate the Bolt Plate 90-degrees or until it stops turning.

Determine the driver/left rear mounting bracket from the illustration on Page 1 and hang it from the two bolt plates using

(2) 12mm Flat Washer, (2) 12mm Lock Washer and (2) 12mm Nut, Carefully position the driver sidebar onto the mounting

brackets and attach it using the included (4) 10 mm x 25mm Hex Head Bolts, (4) 10mm x 22mm OD Flat Washers, and (4)

10mm Lock Washers (Figure 5) . Snug but do not tighten.

6. Align Sidebar properly, and then tighten all hardware.

7. Repeat steps 2 - 8 for the passenger Sidebar.

8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

INSTALLATION INSTRUCTIONS

ARIESOFFROAD

2009-12 HONDA PILOT

PART # S2260

Passenger Side Front

Frame Bracket

10mm Centered Bolt Plate

Passenger Sidebar

(Figure 2)

om the illustration on Page 1. Line up the two holes in the bracket with the

(Figure 3). Snug but do not tighten at this time.

(Figure 4)

. Next insert the 12mm Centered Round End Bolt Plate into the round

Page - 1 -of 2

08/S226008-2

4 12mm Hex Nuts

4 12mm Flat Washers

2 10mm Nuts

10 10mm x 26mm O.D Flat Washers

4 10mm x 35mm Hex Bolts

4 10mm Lock Nuts

8 10mm x 25mm Hex Bolts

8 10mm x 22mm O.D Flat Washers

10 10mm Lock Washers

4 8mm x 25mm Hex Bolts

4 8mm Flat Washers

4 8mm Lock Washers

Driver Side Front

Frame Bracket

12mm Bolt Plate

12m Bolt

Plate

Driver Side Front

Mounting Bracket

Driver Side Rear

Mounting Bracket

Driver Sidebar

Rear

(Figure 1)