Dimplex DS7425DLX Manuale di servizio - Pagina 9
Sfoglia online o scarica il pdf Manuale di servizio per Stufa Dimplex DS7425DLX. Dimplex DS7425DLX 12.
Anche per Dimplex DS7425DLX: Manuale di servizio (12 pagine), Manuale d'uso (14 pagine)
Stampa la pagina
4.
Locate the flicker motor and flicker rod assembly and
remove the wiring clips and connections located by the
heater assembly noting their original locations.
5.
Remove the flicker motor mounting screws and discon-
nect the flicker motor from the flicker rod.
! NOTE: When removing the flicker motor some dam-
age may occur to the flicker rod. If flicker rod is damaged
replace to insure proper operation.
6.
Reassemble in the reverse order as above.
TO REPLACE THERMOSTAT
WARNINg: If unit was operating prior to servicing
allow at least 10 minutes for light bulbs and heating ele-
ment to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
1.
Gently place stove on its back on a flat surface.
2.
Remove the heater cover retaining screws located on
the bottom of the stove and lower heater and light as-
sembly out onto the floor.
3.
Remove all of the mounting screws on the heater cover
and separate the cover from the heater and light as-
sembly.
4.
Locate the thermostat mounted to the heater cover and
disconnect the wiring connections noting their original
locations.
5.
Pull off the thermostat control knob to expose the
mounting screws.
6.
Remove the mounting screws and remove the heater
thermostat.
7.
Properly orient the new thermostat and connect all of
the wiring connections.
8.
Reassemble in the reverse order as above.
TO REPLACE HEATER ASSEMBLY
WARNINg: If unit was operating prior to servicing
allow at least 10 minutes for light bulbs and heating ele-
ment to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
1.
Gently place stove on its back on a flat surface.
2.
Remove the heater cover retaining screws located on
the bottom of the stove and lower heater and light as-
sembly out onto the floor.
3.
Remove all of the mounting screws on the heater cover
and separate the cover from the heater and light as-
sembly.
4.
Locate the heater assembly and disconnect the wiring
connections noting their original locations.
5.
Remove heater mounting bracket screws and set aside
heater assembly.
6.
Properly orient the new heater assembly and connect
all of the wiring clips and connections.
7.
Reassemble in the reverse order as above.
TO REPLACE THE POWER CORD
WARNINg: If unit was operating prior to servicing
allow at least 10 minutes for light bulbs and heating ele-
ment to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
1.
Gently place stove on its back on a flat surface.
2.
Remove the heater cover retaining screws located on
the bottom of the stove and lower heater and light as-
sembly out onto the floor.
3.
Remove all of the mounting screws on the heater cover
and separate the cover from the heater and light as-
sembly.
4.
Locate and disconnect the power cord wiring connec-
tions noting their original locations.
5.
With needle nose pliers grasp the power cord strain
relief grommet from inside the heater cover and push
while twisting to remove.
6.
Pull the power cord out through the hole in the heater
cover.
7.
Install the new power cord through the hole in the
heater cover and connect all of the wiring connections
in their original locations.
8.
Install the power cord retaining grommet on the power
cord and insert into the hole in the heater cover.
9.
Reassemble in the reverse order as above.
TO REPLACE REMOTE CONTROL
RECEIVER
WARNINg: If unit was operating prior to servicing
allow at least 10 minutes for light bulbs and heating ele-
ment to cool off to avoid accidental burning of skin.
WARNINg: Disconnect power before attempting any
maintenance or cleaning to reduce the risk of electric
shock or damage to persons.
1.
Open door by pulling the handles.
2.
Loosen the 2 retainers on the inner sides of the unit by
turning counter clockwise.
3.
Remove 4 screws that secure the top on the rear of the
unit.
4.
Lift the top off of the unit. Carefully remove the partially
reflective glass and store in a safe place to prevent
damage.
5.
Locate the
Remote Control Receiver
the unit.
on the rear wall of
9