Pioneer DEH-3400R Manuale di installazione - Pagina 3

Sfoglia online o scarica il pdf Manuale di installazione per Ricevitore per auto Pioneer DEH-3400R. Pioneer DEH-3400R 6.

Stampa la pagina

Connecting the Units

Note:

Depending on the kind of vehicle, the function

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

2. This Product

1. Rear output

4. Antenna jack

Front output

7. Connect leads of the same

(DEH-3400R)

color to each other.

8. Cap (1*)

When not using this terminal,

do not remove the cap.

9. Yellow (3*)

10. Yellow (2*)

Back-up

To terminal always supplied

(or accessory)

with power regardless of

ignition switch position.

11. Red (5*)

12. Red (4*)

Accessory

To electric terminal controlled

(or back-up)

by ignition switch (12 V DC)

ON/OFF.

13. Black (ground)

To vehicle (metal) body.

14. ISO connector

Note:

15. Yellow/black

In some vehicles, the ISO connector may be

If you use a cellular telephone, connect it via the

divided into two. In this case, be sure to

Audio Mute lead on the cellular telephone. If not,

connect to both connectors.

keep the Audio Mute lead free of any connections.

17. Connecting cords with RCA pin plugs

(sold separately)

18. Power amp

(sold separately)

18. Power amp

(sold separately)

5. Fuse

19. Blue/white

To system control terminal of

the power amp (max. 300 mA

12 V DC).

20. System remote control

21. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

22. Blue/white (6*)

23. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.

24. Front Speaker

(DEH-3400R)

25. Left

26. Right

27. Rear Speaker

28. Perform these connections when using

a different amp (sold separately).

16. Speaker leads

: Front left +

: Rear left +

White

Green

White/black

: Front left ≠

Green/black

: Rear left ≠

Gray

: Front right +

Violet

: Rear right +

Gray/black

: Front right ≠

Violet/black

: Rear right ≠

Connecting the Units

Note:

•

This unit is for vehicles with a 12-volt battery

•

When this product's source is switched ON, a

and negative grounding. Before installing it in a

control signal is output through the blue/white

recreational vehicle, truck, or bus, check the bat-

lead. Connect to an external power amp's system

tery voltage.

remote control or the car's Auto-antenna relay

control terminal (max. 300 mA 12 V DC). If the

•

To avoid shorts in the electrical system, be sure

to disconnect the ≠ battery cable before begin-

car features a glass antenna, connect to the anten-

na booster power supply terminal.

ning installation.

•

When an external power amp is being used with

•

Refer to the owner's manual for details on con-

necting the power amp and other units, then

this system, be sure not to connect the blue/white

lead to the amp's power terminal. Likewise, do

make connections correctly.

not connect the blue/white lead to the power ter-

•

Secure the wiring with cable clamps or adhesive

minal of the auto-antenna. Such connection could

tape. To protect the wiring, wrap adhesive tape

cause excessive current drain and malfunction.

around them where they lie against metal parts.

•

To avoid short-circuiting, cover the disconnected

•

Route and secure all wiring so it cannot touch

lead with insulating tape. Especially, insulate the

any moving parts, such as the gear shift, hand-

unused speaker leads without fail. There is a pos-

brake and seat rails. Do not route wiring in

sibility of short-circuiting if the leads are not

places that get hot, such as near the heater outlet.

insulated.

If the insulation of the wiring melts or gets torn,

•

If this unit is installed in a vehicle that does not

there is a danger of the wiring short-circuiting to

have an ACC (accessory) position on the ignition

the vehicle body.

switch, the red lead of the unit should be con-

•

Don't pass the yellow lead through a hole into

nected to a terminal coupled with ignition switch

the engine compartment to connect to the battery.

ON/OFF operations. If this is not done, the vehi-

This will damage the lead insulation and cause a

cle battery may be drained when you are away

very dangerous short.

from the vehicle for several hours.

•

Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

•

Never feed power to other equipment by cutting

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

•

When replacing fuse, be sure to use only fuse of

the rating prescribed on this product.

•

Since a unique BPTL circuit is employed, never

ACC position

wire so the speaker leads are directly grounded

or the left and right ≠ speaker leads are com-

•

The black lead is ground. Please ground this lead

mon.

separately from the ground of high-current prod-

•

Speakers connected to this unit must be high-

ucts such as power amps.

power types with minimum rating of 45W

If you ground the products together and the

(50 W)* and impedance of 4 to 8 ohms.

ground becomes detached, there is a risk of dam-

Connecting speakers with output and/or imped-

age to the products or fire.

ance values other than those noted here may

result in the speakers

catching fire, emitting smoke or becoming dam-

aged.

•

Cords for this product and those for other prod-

* DEH-3400R

ucts may be different colors even if they have

the same function. When connecting this prod-

uct to another product, refer to the supplied

Installation manuals of both products and con-

nect cords that have the same function.

Fig. 5

Abb. 5

Afb. 5

Connection Diagram (Fig. 5)

1. Rear output

2. This product

3. Front output (DEH-3400R)

4. Antenna jack

5. Fuse

6. Note:

Depending on the kind of vehicle, the function of

3* and 5* may be different. In this case, be sure

to connect 2* to 5* and 4* to 3*.

7. Connect leads of the same color to each other.

8. Cap (1*)

When not using this terminal, do not remove the

cap.

9. Yellow (3*)

Back-up (or accessory)

10. Yellow (2*)

To terminal always supplied with power regard-

less of ignition switch position.

11. Red (5*)

Accessory (or back-up)

12. Red (4*)

To electric terminal controlled by ignition switch

(12 V DC) ON/OFF.

13. Black (ground)

To vehicle (metal) body.

14. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to connect

to both connectors.

15. Yellow/black

If you use a cellular telephone, connect it via the

No ACC position

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connec-

tions.

16. Speaker leads

: Front left +

White

White/black : Front left ≠

Gray

: Front right +

Gray/black : Front right ≠

: Rear left +

Green

Green/black : Rear left ≠

: Rear right +

Violet

Violet/black : Rear right ≠

17. Connecting cords with RCA pin plugs (sold

separately)

18. Power amp (sold separately)

19. Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

20. System remote control

21. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

22. Blue/white (6*)

23.The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and

7* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 6* and 7*.

24. Front speaker (DEH-3400R)

25. Left

26. Right

27. Rear Speaker

28. Perform these connections when using a different

amp (sold separately).