Pioneer DEH-7200SD Manuale operativo - Pagina 15

Sfoglia online o scarica il pdf Manuale operativo per Ricevitore per auto Pioneer DEH-7200SD. Pioneer DEH-7200SD 28. Cd rds receiver
Anche per Pioneer DEH-7200SD: Manuale di avvio rapido (9 pagine), Manuale di installazione (8 pagine)

Stampa la pagina

Operating this unit

You can adjust the currently selected equalizer curve

setting as desired. Adjusted equalizer curve settings

are memorized in Custom1 or Custom2.

! A separate Custom1 curve can be created for

each source. If you make adjustments when a

curve other than Custom2 is selected, the equali-

zer curve settings will be memorized in Custom1.

! A Custom2 curve can be created common to all

sources. If you make adjustments when the Cus-

tom2 curve is selected, the Custom2 curve will

be updated.

1 Recall the equalizer curve you want to adjust.

2 Push M.C. left or right to select the equalizer

band to adjust.

100Hz—315Hz—1.25kHz—3.15kHz—8kHz

3 Push M.C. up or down to adjust the equalizer

curve.

+6 to –6 is displayed as the equalizer curve is in-

creased or decreased.

LOUD (loudness)

Loudness compensates for deficiencies in the low-

and high-frequency ranges at low volume.

1 Press M.C. to turn loudness on or off.

2 Push M.C. left or right to select the desired set-

ting.

Low (low)—Mid (mid)—High (high)—OFF (off)

Sub W.1 (subwoofer on/off setting)

This unit is equipped with a subwoofer output which

can be turned on or off.

1 Press M.C. to turn subwoofer output on or off.

2 Push M.C. left or right to select the phase of sub-

woofer output.

Push M.C. left to select reverse phase and Re-

verse appears in the display. Push M.C. right to

select normal phase and Normal appears in the

display.

Sub W.2 (subwoofer adjustment)

When the subwoofer output is on, you can adjust the

cut-off frequency and the output level of the subwoo-

fer.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

1 Push M.C. left or right to select cut-off frequency.

50Hz—63Hz—80Hz—100Hz—125Hz

2 Push M.C. up or down to adjust the output level

of the subwoofer.

Each time M.C. is pushed up or down, subwoofer

level increases or decreases. +6 to -24 is dis-

played as the level is increased or decreased.

Bass (bass boost)

1 Push M.C. up or down to select a desired level.

0 to +6 is displayed as the level is increased or de-

creased.

HPF (high pass filter adjustment)

When you do not want low sounds from the subwoo-

fer output frequency range to play from the front or

rear speakers, turn on the HPF (high pass filter). Only

frequencies higher than those in the selected range

are output from the front or rear speakers.

1 Press M.C. to turn high pass filter on or off.

2 Push M.C. left or right to select cut-off frequency.

50Hz—63Hz—80Hz—100Hz—125Hz

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the vo-

lume level of each source to prevent radical changes

in volume when switching between sources.

! Settings are based on the FM volume level, which

remains unchanged.

Before adjusting source levels, compare the FM

volume level with the level of the source you wish

to adjust.

! The MW/LW volume level can also be adjusted

with source level adjustments.

1 Push M.C. up or down to adjust the source vo-

lume.

Adjustment range: +4 to –4

Note

When selecting FM as the source, you cannot

switch to SLA.

Initial Settings

1 Function display

! Shows the function status.

Press SRC/OFF and hold until the unit

turns off.

Press M.C. and hold until the initial set-

ting menu appears in the display.

Section