Pioneer DEH-P4650MP Manuale di installazione

Sfoglia online o scarica il pdf Manuale di installazione per Ricevitore per auto Pioneer DEH-P4650MP. Pioneer DEH-P4650MP 5. Car radio

Stampa la pagina

DEH-P4690MP

DEH-P4650MP

This product conforms to new cord colors.

Los colores de los cables de este producto se

conforman con un nuevo código de colores.

As cores dos fios deste produto seguem um novo

padrão de cores.

Æ...b¹b'« „öÝô« Ê«

uÃ« lÄ "UN'« «c¼ r− M¹

Printed in

<XRD7023-A/JS> ES

60°

Fig. 1

Fig. 3

± qJAÃ«

≥ qJAÃ«

182

Fig. 2

Fig. 4

≤ qJAÃ«

¥ qJAÃ«

Fig. 5

µ qJAÃ«

Fig. 6

∂ qJAÃ«

Installation

Note:

•

Before finally installing the unit, connect the

wiring temporarily, making sure it is all connect-

ed up properly, and the unit and the system work

properly.

•

Use only the parts included with the unit to

ensure proper installation. The use of unautho-

rized parts can cause malfunctions.

•

Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

•

Install the unit where it does not get in the dri-

ver's way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

•

The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

— for instance, near a heater outlet.

•

If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.

(Fig. 1)

•

When installing, to ensure proper heat dispersal

Fig. 7

when using this unit, make sure you leave ample

space behind the rear panel and wrap any loose

∑ qJAÃ«

cables so they are not blocking the vents.

DIN Front/Rear-mount

This unit can be properly installed either from

"Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing

threaded screw holes at the sides of unit chassis).

For details, refer to the following illustrated

installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 2)

1. Dashboard

2. Holder

After inserting the holder into the dashboard,

then select the appropriate tabs according to the

thickness of the dashboard material and bend

them.

(Install as firmly as possible using the top and

bottom tabs. To secure, bend the tabs 90

degrees.)

3. Rubber bush

4. Screw

Removing the Unit (Fig. 3) (Fig. 4)

5. Frame

6. Insert the release pin into the hole in the bottom

of the frame and pull out to remove the frame.

(When reattaching the frame, point the side with

a groove downwards and attach it.)

7. Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into place.

Keeping the keys pressed against the sides of the

unit, pull the unit out.

DIN Rear-mount

Installation using the screw holes on

the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)

1. Remove the frame.

8. Frame

9. Insert the release pin into the hole in the bottom

of the frame and pull out to remove the frame.

(When reattaching the frame, point the side with

a groove downwards and attach it.)

2. Fastening the unit to the factory

radio mounting bracket.

10. Select a position where the screw holes of the

bracket and the screw holes of the head unit

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either truss

screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw

holes in the bracket.

11. Screw

12. Factory radio mounting bracket

13. Dashboard or Console